Analog.com Analog Dialogue Wiki 简体中文
EngineerZone
EngineerZone
  • Log in
  • Site
  • Search
  • Log in
  • Home
  • Blogs ⌵
    • EngineerZone Spotlight
    • The Engineering Mind
    • Analog Garage
  • Browse ⌵
    • All Groups
    • All Members
  • Support ⌵
    • 3D ToF Depth Sensing
    • Amplifiers
    • Analog Microcontrollers
    • Audio
    • Clock and Timing
    • Data Converters
    • Design Tools and Calculators
    • Direct Digital Synthesis (DDS)
    • Embedded Vision Sensing
    • Energy Monitoring and Metering
    • FPGA Reference Designs
    • Industrial Ethernet
    • Interface and Isolation
    • Low Power RF Transceivers
    • MeasureWare
    • MEMS Inertial Sensors
    • Motor Control Hardware Platforms
    • Optical Sensing
    • Power By Linear
    • Processors and DSP
    • Reference Circuits
    • RF and Microwave
    • Switches/Multiplexers
    • Temperature Sensors
    • Video
    • Wireless Sensor Networks Reference Library
  • My EZ
  • More
  • Cancel
SHARC Processors
  • Processors and DSP
  • More
SHARC Processors
Documents FAQ: Using the Expert Code Generator (EE-322) and Expert DAI (EE-243) plugins for VisualDSP++ in Windows Vista, Windows 7 and Windows 8
  • Q&A
  • Discussions
  • Documents
  • File Uploads
  • Video/Images
  • Sub-Groups
  • Tags
  • Reports
  • More
  • Cancel
  • New
SHARC Processors requires membership for participation - click to join
  • Documents
  • 214xx IIR Accelerator -  how to use the save state operation ?
  • 214xx processors: pull down resistor at SPI_CLK(DPI3) pin may result in SPI master boot failure
  • ADSP-21469 DDR2 controller-  How to configure bit 0 of the DDR2CTL3 register
  • ADSP-SC58x FFTA Benchmarks
  • Example of using I2S PCG and SPORT interrupts
  • FAQ: Does ADI provide USB VID/PID?
  • FAQ: Flash read/prgm via JTAG
  • FAQ: I'm interested in the SHARC processor family but don’t know where to start?
  • FAQ: Is it possible to program the internal ROM on the SHARC family 2126x, 2136x, 2137x and 2146x Processors?
  • FAQ: Standard Math Library for SHARC
  • FAQ: Using the Expert Code Generator (EE-322) and Expert DAI (EE-243) plugins for VisualDSP++ in Windows Vista, Windows 7 and Windows 8
  • FAQ: Why do the January, 2018 ADSP-214xx anomaly lists look so different?
  • FAQ:  ADSP-21369 EZKit expansion port dimensions
  • FAQ:  How do I debug an application which is not booting properly?
  • How to configure SRU for using TWI on SHARC processors?
  • If the breakpoint is anywhere in the area of code that the CRC is being checked on, then there could be a problem.
  • New SHARC Hardware Reference released
  • Programming PLL on ADSP-214xx processors
  • SHARC PROCESSORS
  • SPI serial flash driver & SAFP python script
  • The ADSP-21469 datasheet rev 0 shows tMCFDZ (DAT/SIG Output Time to Three-state)  parameter to be 15ns. However, MediaLB specs require this value for 1024*fs to be less than 6.1ns. Is this a concern?
  • What is the difference between ADSP-21371KSWZ-2A and ADSP-21371KSWZ-2B
  • What is the maximum allowed serial port  (SPORT) clock (SCLK) frequency for SHARC processors ?

FAQ: Using the Expert Code Generator (EE-322) and Expert DAI (EE-243) plugins for VisualDSP++ in Windows Vista, Windows 7 and Windows 8

Question

I am attempting to register the plugin DLLs (AdvancedExpertDAI.dll, ACC_Init.dll, PLL_DDR2_SDRAM_AMI_Init.dll) associated with the application notes "EE-243 - Using the Expert DAI for SHARC Processors" and "EE-322 - Expert Code Generator for SHARC Processors", but I receive the following error when calling regsvr32.exe from the command line:

"The module <moduleName> was loaded but the call to DllRegisterServer failed with error code 0x80020009. For more information about this problem, search online using the error code as a search term".

===============================

Answer

As explained in the accompanying application note, which can be found in our Technical Library, when registering these DLLs you need to ensure that you launch the Command Prompt using the "Run as Administrator" feature. This is selected by right-clicking on the "Command Prompt" and selecting "Run as Administrator", as shown here:

This is necessary when registering these plugins with VisualDSP++ tools when running Windows Vista, Windows 7, and Windows 8 Operating Systems.

Note: you must explicitly select the "Run as Administrator" option. Windows Vista, Windows 7, and Windows 8 impose Registry restrictions, even for Administrator users.

  • Share
  • History
  • More
  • Cancel
Comments
Anonymous
Related
 
Social
Quick Links
  • About ADI
  • Partners
  • Analog Dialogue
  • Careers
  • Contact us
  • Investor Relations
  • News Room
  • Quality & Reliability
  • Sales & Distribution
  • Analog Garage
Languages
  • English
  • 简体中文
  • 日本語
  • Руccкий
Newsletters

Interested in the latest news and articles about ADI products, design tools, training and events? Choose from one of our 12 newsletters that match your product area of interest, delivered monthly or quarterly to your inbox.

Sign Up
Switch to mobile view
Analog Logo
© 1995 - 2019 Analog Devices, Inc. All Rights Reserved 沪ICP备09046653号
  • ©
  • 1995 - 2019 Analog Devices, Inc. All Rights Reserved
  • 沪ICP备09046653号
  • Sitemap
  • Privacy & Security
  • Privacy Settings
  • Terms of use
EngineerZone Uses cookies to ensure you get the best experience in our community. For more information on cookies, please read our Privacy & Security Statement.