• State Verified Answer
  • Replies 28 replies
  • Subscribers 37 subscribers
  • Views 2891 views
  • Users 0 members are here
Options
Similar Content 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
CCLK for ADSP-21489 is not manipulated as per PMCTL config in my target board.



		

			

									
					    satya
					
							

			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Jan 2, 2013 
				
			
			
		
    

				
		
    
		    		    
		    
		    	
			
    Dear Sir,
    
 
    Please provide me guidance on the above subject, I tried to evaluate the target board with small application code. It is working fine as per application requirement when I port in evaluation board for ADSP-21489. But the same thing is not working on target board. The reason what I found during preliminary check is its not generating the CCLK as per requirement.
    
 
    please suggest any additional check up to do and guide to sort this problem.
    
 
    regards
    
 
    satya
    
								
    

				
				
		
    
			
						
									
									
						
						
			
			
			
			
		
    

        
        

					
    
			
    


    


	
    
		
	
    















    
	
    
	
    
					



			








	
	
	
	



Parents
	
      
	

    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
        
            
			                            
                        
                on Jan 25, 2013 10:00 AM
            
            
					
        
	
        

		
		
        
					
        Dear Sir,
        
 
        I didn't try your simple code on custom board for validation of Flash memory, Since then onwards our custom board giving problem. We are on job to solve the problem, but till now it show casing same problem.
        
 
        The problem is "we generated power supply required for ADSP 21489 i.e 3.3V and 1.1V from ADP2114 IC (Schematic is attached). When it is power on after some duration both ADSP21489 and ADP2114 goes off. 
        
 
        We verified the output of ADP2114 circuit at 3.3V and 1.1V with 300mA ripple with no load conditions (means when there is no ADSP21489 IC in custom board).
        
 
        please let me know, if in any case either of two supplies 3.3V and 1.1V in that if any one supply is not available to ADSP21489 then processor IC will goes off?. What will be the condition of processor IC.
        
 
        please suggest the necessary safety measures to solve our problem.
        
 
        regards
        
 
        satya 
        
			
        

		
		
		
		
	
        
	
        
		
        
			
		
        
	
        
	
        
		
						
						
				
						
				
				
		
		
        
			
		
        
	
        

        

        • 

	
      



Reply

        


      • 
	
        



	
		
	
	



        
	
        
		
        
							
					
        
		
        
			
													0
							
			
				
									
							        
			
			
			
          
            
			                            
                        
                on Jan 25, 2013 10:00 AM
            
            
					
          
	
          

		
		
          
					
          Dear Sir,
          
 
          I didn't try your simple code on custom board for validation of Flash memory, Since then onwards our custom board giving problem. We are on job to solve the problem, but till now it show casing same problem.
          
 
          The problem is "we generated power supply required for ADSP 21489 i.e 3.3V and 1.1V from ADP2114 IC (Schematic is attached). When it is power on after some duration both ADSP21489 and ADP2114 goes off. 
          
 
          We verified the output of ADP2114 circuit at 3.3V and 1.1V with 300mA ripple with no load conditions (means when there is no ADSP21489 IC in custom board).
          
 
          please let me know, if in any case either of two supplies 3.3V and 1.1V in that if any one supply is not available to ADSP21489 then processor IC will goes off?. What will be the condition of processor IC.
          
 
          please suggest the necessary safety measures to solve our problem.
          
 
          regards
          
 
          satya 
          
			
          

		
		
		
		
	
          
	
          
		
          
			
		
          
	
          
	
          
		
						
						
				
						
				
				
		
		
          
			
		
          
	
          

          

          • 


        


Children
	
        No Data