• State Verified Answer
  • Replies 4 replies
  • Subscribers 37 subscribers
  • Views 837 views
  • Users 0 members are here
Options
Similar Content 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
ADSP-21469 not booting after being programmed



		

			

									
					    JRyall
					
							

			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Mar 9, 2018 
				
			
			
		
    

				
		
    
		    		    
		    
		    	
			
    I programmed my ADSP-21469 EzKit successfully using the CLDP and an ICE-1000. I set the loader file up to program the parallel flash memory. The command line reported that the programming was done. I set the boot switch (sw4) to position 2 for booting from the parallel flash memory. Then I reset my board.
    
 
    Unfortunately it seems that either the program didn't take, or the board isn't booting. I'm not sure what the problem is but the program runs fine when I run it though CCES and the emulator, but I just can't seem to get it to run on it's own. Any help you can give me would be much appreciated.
    
								
    

				
				
		
    
			
						
									
									
						
						
			
			
			
			
		
    

        
        

					
    
			
    


    


	
    
		
	
    















    
	
    
	
    
					



			








	
	
	
	



Parents
	
      
	

    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
			                            
                        
                on Mar 19, 2018 3:10 AM
            
            
					
      
	
      

		
		
      
					
      Please see my comments.
      
 
      1) I don't think you are not using correct diver file for parallel flash.  Looking at the image showed above, seems the driver file is for SPI flash (M25P16).
      
 
      Please use the driver file for parallel flash (M29W320) from the below path,
      
 
      <ADSP-21469 BSP installation directory>\ADSP-21469_EZKIT-Rel1.0.0\21469_EZ-Board\Examples\Device_Programmer\parallel\21469_m29w320_dpia.dxe
      
 
      2) Please confirm if you have modified the driver file that you used above. Just wondering how it shows the DevCode, ManCode and all stuffs?
      
 
      Best Regards,
      
 
      Jithul
      
 
       
      
			
      

		
		
		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
				
						
				
				
		
		
      
			
		
      
	
      

      

      • 

	
    



Reply

      


    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
      •  Analog Employees  
      
            
			                            
                        
                on Mar 19, 2018 3:10 AM
            
            
					
      
	
      

		
		
      
					
      Please see my comments.
      
 
      1) I don't think you are not using correct diver file for parallel flash.  Looking at the image showed above, seems the driver file is for SPI flash (M25P16).
      
 
      Please use the driver file for parallel flash (M29W320) from the below path,
      
 
      <ADSP-21469 BSP installation directory>\ADSP-21469_EZKIT-Rel1.0.0\21469_EZ-Board\Examples\Device_Programmer\parallel\21469_m29w320_dpia.dxe
      
 
      2) Please confirm if you have modified the driver file that you used above. Just wondering how it shows the DevCode, ManCode and all stuffs?
      
 
      Best Regards,
      
 
      Jithul
      
 
       
      
			
      

		
		
		
		
	
      
	
      
		
      
			
		
      
	
      
	
      
		
						
						
				
						
				
				
		
		
      
			
		
      
	
      

      

      • 


    


Children
	
    No Data