• State Verified Answer
  • Replies 4 replies
  • Subscribers 37 subscribers
  • Views 823 views
  • Users 0 members are here
Options
Similar Content 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
ADSP-21469 not booting after being programmed



		

			

									
					    JRyall
					
							

			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Mar 9, 2018 
				
			
			
		
    

				
		
    
		    		    
		    
		    	
			
    I programmed my ADSP-21469 EzKit successfully using the CLDP and an ICE-1000. I set the loader file up to program the parallel flash memory. The command line reported that the programming was done. I set the boot switch (sw4) to position 2 for booting from the parallel flash memory. Then I reset my board.
    
 
    Unfortunately it seems that either the program didn't take, or the board isn't booting. I'm not sure what the problem is but the program runs fine when I run it though CCES and the emulator, but I just can't seem to get it to run on it's own. Any help you can give me would be much appreciated.
    
								
    

				
				
		
    
			
						
									
									
						
						
			
			
			
			
		
    

        
        

					
    
			
    


    


	
    
		
	
    















    
	
    
	
    
					



			








	
	
	
	



Parents
	
      
	

    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
        
            
			                            
                        
                on Mar 17, 2018 11:22 PM
            
            
					
        
	
        

		
		
        
					
        I loaded the file that you sent me onto the ADSP-21469. I had to modify the script txt slightly by pointing it to the driver dxe I have here, and to use the ICE-1000.
        
 
        
 
        Everything seems to have gone okay with the deployment.
        
 
        I hit the reset button on the board but the LED turned on and stayed green. Should it be flashing on and off if it booted the program here?
        
			
        

		
		
		
		
	
        
	
        
		
        
			
		
        
	
        
	
        
		
						
						
				
						
				
				
		
		
        
			
		
        
	
        

        

        • 

	
      



Reply

        


      • 
	
        



	
		
	
	



        
	
        
		
        
							
					
        
		
        
			
													0
							
			
				
									
							        
			
			
			
          
            
			                            
                        
                on Mar 17, 2018 11:22 PM
            
            
					
          
	
          

		
		
          
					
          I loaded the file that you sent me onto the ADSP-21469. I had to modify the script txt slightly by pointing it to the driver dxe I have here, and to use the ICE-1000.
          
 
          
 
          Everything seems to have gone okay with the deployment.
          
 
          I hit the reset button on the board but the LED turned on and stayed green. Should it be flashing on and off if it booted the program here?
          
			
          

		
		
		
		
	
          
	
          
		
          
			
		
          
	
          
	
          
		
						
						
				
						
				
				
		
		
          
			
		
          
	
          

          

          • 


        


Children
	
        No Data