FAQ: [#6870] Fail to init device hci0 for bluetooth test in bf537-stamp with usb isp1362(2011)

Document created by Aaronwu Employee on Sep 12, 2013
Version 1Show Document
  • View in full screen mode

[#6870] Fail to init device hci0 for bluetooth test in bf537-stamp with usb isp1362

Submitted By: Vivi Li

Open Date

2011-11-08 03:07:37    

Priority:

Low     Assignee:

Bob Liu

Status:

Open     Fixed In Release:

N/A

Found In Release:

2011R1     Release:

Category:

N/A     Board:

N/A

Processor:

BF537     Silicon Revision:

Is this bug repeatable?:

Yes     Resolution:

Assigned (Not Start)

Uboot version or rev.:

    Toolchain version or rev.:

gcc4.3-2011R1-RC2

App binary format:

N/A     

Summary: Fail to init device hci0 for bluetooth test in bf537-stamp with usb isp1362

Details:

 

Fail to init device hci0 for bluetooth test in bf537-stamp with usb isp1362.

This should happen in both trunk and 2011r1 branch.

 

--

Linux version 3.0.8-ADI-2011R1-svn10140 (test@54-7393-1362-sl811-jtag) (gcc version 4.3.5 (ADI-2011R1-RC2) ) #30 Mon Nov 7 06:061

register early platform devices

bootconsole [early_shadow0] enabled

bootconsole [early_BFuart0] enabled

early printk enabled on early_BFuart0

Limiting kernel memory to 56MB due to anomaly 05000263

Board Memory: 64MB

Kernel Managed Memory: 64MB

Memory map:

  fixedcode = 0x00000400-0x00000490

  text      = 0x00001000-0x0015da80

  rodata    = 0x0015da80-0x001c9d38

  bss       = 0x001ca000-0x001da060

  data      = 0x001da060-0x001ee000

    stack   = 0x001ec000-0x001ee000

  init      = 0x001ee000-0x00a27000

  available = 0x00a27000-0x03800000

  DMA Zone  = 0x03f00000-0x04000000

Hardware Trace active and enabled

Boot Mode: 0

Blackfin support (C) 2004-2010 Analog Devices, Inc.

Compiled for ADSP-BF537 Rev 0.2

Blackfin Linux support by http://blackfin.uclinux.org/

Processor Speed: 500 MHz core clock and 125 MHz System Clock

NOMPU: setting up cplb tables

Instruction Cache Enabled for CPU0

  External memory: cacheable in instruction cache

Data Cache Enabled for CPU0

  External memory: cacheable (write-back) in data cache

Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 14224

Kernel command line: root=/dev/mtdblock0 rw clkin_hz=25000000 earlyprintk=serial,uart0,57600 console=ttyBF0,57600 ip=10.100.4.50f

PID hash table entries: 256 (order: -2, 1024 bytes)

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory available: 46340k/65536k RAM, (8420k init code, 1394k kernel code, 578k data, 1024k dma, 7780k reserved)

NR_IRQS:146

Configuring Blackfin Priority Driven Interrupts

bfin-rtc: invalid date; resetting

console [ttyBF0] enabled, bootconsole disabled

console [ttyBF0] enabled, bootconsole disabled

Calibrating delay loop... 995.32 BogoMIPS (lpj=1990656)

pid_max: default: 32768 minimum: 301

Mount-cache hash table entries: 512

Blackfin Scratchpad data SRAM: 4 KB

Blackfin L1 Data A SRAM: 16 KB (16 KB free)

Blackfin L1 Data B SRAM: 16 KB (16 KB free)

Blackfin L1 Instruction SRAM: 48 KB (35 KB free)

NET: Registered protocol family 16

Blackfin DMA Controller

stamp_init(): registering device resources

bio: create slab <bio-0> at 0

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

Bluetooth: Core ver 2.16

NET: Registered protocol family 31

Bluetooth: HCI device and connection manager initialized

Bluetooth: HCI socket layer initialized

Bluetooth: L2CAP socket layer initialized

Bluetooth: SCO socket layer initialized

Switching to clocksource bfin_cs_cycles

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

UDP hash table entries: 256 (order: 0, 4096 bytes)

UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

NET: Registered protocol family 1

debug-mmrs: setting up Blackfin MMR debugfs

msgmni has been set to 90

io scheduler noop registered (default)

bfin-uart: Blackfin serial driver

bfin-uart.0: ttyBF0 at MMIO 0xffc00400 (irq = 18) is a BFIN-UART

brd: module loaded

bfin_mii_bus: probed

bfin_mac: attached PHY driver [SMSC LAN83C185] (mii_bus:phy_addr=0:01, irq=-1, mdc_clk=2500000Hz(mdc_div=24)@sclk=125MHz)

bfin_mac bfin_mac.0: eth0: Blackfin on-chip Ethernet MAC driver, Version 1.1

driver isp1362-hcd, 2005-04-04

isp1362-hcd isp1362-hcd.0: ISP1362 Host Controller

isp1362-hcd isp1362-hcd.0: new USB bus registered, assigned bus number 1

isp1362_hc_reset:

isp1362-hcd isp1362-hcd.0: irq 53, io mem 0x20360000

isp1362_hc_start:

isp1362-hcd isp1362-hcd.0: ISP1362 Memory usage:

isp1362-hcd isp1362-hcd.0:   ISTL:    2 *  256:      512 @ $0000:$0100

isp1362-hcd isp1362-hcd.0:   INTL:   16 * ( 64+8):  1152 @ $0200

isp1362-hcd isp1362-hcd.0:   ATL :   32 * ( 64+8):  2304 @ $0680

isp1362-hcd isp1362-hcd.0:   USED/FREE:   3968       128

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

ISP1362 Host Controller, irq 53

sl811: driver sl811-hcd, 19 May 2005

sl811-hcd sl811-hcd.0: SL811HS v1.5

sl811-hcd sl811-hcd.0: new USB bus registered, assigned bus number 2

sl811-hcd sl811-hcd.0: irq 54, io mem 0x20340000

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 1 port detected

rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0

bfin-wdt: initialized: timeout=20 sec (nowayout=0)

Bluetooth: Generic Bluetooth USB driver ver 0.6

usbcore: registered new interface driver btusb

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

TCP cubic registered

NET: Registered protocol family 17

Bluetooth: RFCOMM TTY layer initialized

usb 1-2: new full speed USB device number 2 using isp1362-hcd

Bluetooth: RFCOMM socket layer initialized

Bluetooth: RFCOMM ver 1.11

Bluetooth: BNEP (Ethernet Emulation) ver 1.3

Bluetooth: BNEP filters: protocol multicast

Bluetooth: HIDP (Human Interface Emulation) ver 1.2

rtc-bfin rtc-bfin: setting system clock to 1970-01-01 11:09:58 UTC (40198)

IP-Config: Complete:

     device=eth0, addr=10.100.4.50, mask=255.255.255.0, gw=10.100.4.174,

     host=bf537-stamp, domain=, nis-domain=(none),

     bootserver=10.100.4.174, rootserver=10.100.4.174, rootpath=

dma_alloc_init: dma_page @ 0x02a70000 - 256 pages at 0x03f00000

Freeing unused kernel memory: 8420k freed

usb 2-1: new full speed USB device number 2 using sl811-hcd

usb 2-1: device descriptor read/64, error -62

                           _____________________________________

        a8888b.           / Welcome to the uClinux distribution \

       d888888b.         /       _     _                         \

       8P"YP"Y88        /       | |   |_|            __  __ (TM)  |

       8|o||o|88  _____/        | |    _ ____  _   _ \ \/ /       |

       8'    .88       \        | |   | |  _ \| | | | \  /        |

       8`._.' Y8.       \       | |__ | | | | | |_| | /  \        |

      d/      `8b.       \      \____||_|_| |_|\____|/_/\_\       |

     dP   .    Y8b.       \   For embedded processors including   |

    d8:'  "  `::88b        \    the Analog Devices Blackfin      /

   d8"         'Y88b        \___________________________________/

  :8P    '      :888

   8a.   :     _a88P         For further information, check out:

._/"Yaa_:   .| 88P|            - http://blackfin.uclinux.org/

\    YP"    `| 8P  `.          - http://docs.blackfin.uclinux.org/

/     \.___.d|    .'           - http://www.uclinux.org/

`--..__)8888P`._.'  jgs/a:f    - http://www.analog.com/blackfin

 

Have a lot of fun...

 

 

BusyBox v1.18.4 (2011-11-07 04:55:38 CST) hush - the humble shell

 

root:/> PHY: 0:01 - Link is Up - 100/Full

 

root:/>

root:/>

root:/> hciconfig hci0 up

hci_cmd_timer: hci0 command tx timeout

hci_cmd_timer: hci0 command tx timeout

hci_cmd_timer: hci0 command tx timeout

hci_cmd_timer: hci0 command tx timeout

hci_cmd_timer: hci0 command tx timeout

hci_cmd_timer: hci0 command tx timeout

hci_cmd_timer: hci0 command tx timeout

hci_cmd_timer: hci0 command tx timeout

hci_cmd_timer: hci0 command tx timeout

Can't init device hci0: Connection timed out (110)

root:/> hci_cmd_timer: hci0 command tx timeout

 

root:/> version

kernel:    Linux release 3.0.8-ADI-2011R1-svn10140, build #30 Mon Nov 7 06:06:15 CST 2011

toolchain: bfin-uclinux-gcc release gcc version 4.3.5 (ADI-2011R1-RC2)

user-dist: release svn-10477, build #414 Mon Nov 7 06:04:59 CST 2011

root:/>

--

 

Follow-ups

 

--- Sonic Zhang                                              2011-11-10 01:30:14

Temporary workaround is to run "hciconfig hci0 up" twice.

 

 

 

    Files

    Changes

    Commits

    Dependencies

    Duplicates

    Associations

    Tags

 

File Name     File Type     File Size     Posted By

config.config.bluetooth    application/octet-stream    51926    Vivi Li

config.linux.bluetooth    application/octet-stream    42484    Vivi Li

Outcomes