2008-12-18 15:54:39     548 EZKIT - Booting from vmImage got stuck

Document created by Aaronwu Employee on Aug 9, 2013
Version 1Show Document
  • View in full screen mode

2008-12-18 15:54:39     548 EZKIT - Booting from vmImage got stuck

AC CHAO (UNITED STATES)

Message: 66875   

 

Hello,

 

Below is the boot up console message.

 

I just tried to follow the nfs example in http://docs.blackfin.uclinux.org/doku.php?id=uclinux-dist:nfs

 

Could you advise where I should check?

 

Thank you.

 

 

 

Regards,

 

 

 

AC

 

 

U-Boot 1.1.6-svn1273 (ADI-2008R1.5) (Jul 21 2008 - 00:35:28)

 

CPU:   ADSP bf548-0.0 (Detected Rev: 0.1)

Board: ADI BF548 EZ-Kit board

       Support: http://blackfin.uclinux.org/

Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz

RAM:   64 MB

Flash: 16 MB

NAND:  256 MiB

In:    serial

Out:   serial

Err:   serial

Net:   LAN9x18 (0x118a0000) detected at 0x24000000

MAC:   00:E0:22:FE:BD:ED

Hit any key to stop autoboot:  0

start Auto negotiation... (take ‾2sec)

Auto negotiation complete, 100BaseTX, full duplex

TFTP from server 192.168.1.63; our IP address is 192.168.1.64

Filename 'vmImage'.

Load address: 0x1000000

Loading: #################################################################

     #################################################################

     #################################################################

     #################################################################

     ####################################

done

Bytes transferred = 1510597 (170cc5 hex)

## Booting image at 01000000 ...

   Image Name:   Linux-2.6.22.19-ADI-2008R1.5-svn

   Created:      2008-12-18  19:13:12 UTC

   Image Type:   Blackfin Linux Kernel Image (gzip compressed)

   Data Size:    1510533 Bytes =  1.4 MB

   Load Address: 00001000

   Entry Point:  00284000

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK

Starting Kernel at = 284000

 

QuoteReplyEditDelete

 

 

2008-12-18 15:58:51     Re: 548 EZKIT - Booting from vmImage got stuck

Mike Frysinger (UNITED STATES)

Message: 66876   

 

please rerad:

http://docs.blackfin.uclinux.org/doku.php?id=linux-kernel:debug:post_mortem

QuoteReplyEditDelete

 

 

2008-12-18 16:22:44     Re: 548 EZKIT - Booting from vmImage got stuck

AC CHAO (UNITED STATES)

Message: 66878   

 

Hi Mike,

 

Thanks  a lot for advice. I just found I forgot to add 'console=ttyBF0,57600' in U-Boot.

 

Now I can see the console message, but now is another error. The console message is as below:

 

Thank you.

 

 

 

Regards,

 

 

 

AC

 

 

 

U-Boot 1.1.6-svn1273 (ADI-2008R1.5) (Jul 21 2008 - 00:35:28)

 

CPU:   ADSP bf548-0.0 (Detected Rev: 0.1)

Board: ADI BF548 EZ-Kit board

       Support: http://blackfin.uclinux.org/

Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz

RAM:   64 MB

Flash: 16 MB

NAND:  256 MiB

In:    serial

Out:   serial

Err:   serial

Net:   LAN9x18 (0x118a0000) detected at 0x24000000

MAC:   00:E0:22:FE:BD:ED

Hit any key to stop autoboot:  0

start Auto negotiation... (take ‾2sec)

Auto negotiation complete, 100BaseTX, full duplex

TFTP from server 192.168.1.63; our IP address is 192.168.1.64

Filename 'vmImage'.

Load address: 0x1000000

Loading: #################################################################

     #################################################################

     #################################################################

     #################################################################

     ####################################

done

Bytes transferred = 1510597 (170cc5 hex)

## Booting image at 01000000 ...

   Image Name:   Linux-2.6.22.19-ADI-2008R1.5-svn

   Created:      2008-12-18  19:13:12 UTC

   Image Type:   Blackfin Linux Kernel Image (gzip compressed)

   Data Size:    1510533 Bytes =  1.4 MB

   Load Address: 00001000

   Entry Point:  00284000

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK

Starting Kernel at = 284000

Linux version 2.6.22.19-ADI-2008R1.5-svn (ac@ac-desktop) (gcc version 4.1.2 (ADI svn)) #132 Thu Dec 18 11:13:08 PST 2008

Hardware Trace Active and Enabled

Blackfin support (C) 2004-2007 Analog Devices, Inc.

Compiled for ADSP-BF548 Rev 0.0

Warning: Compiled for Rev 0, but running on Rev 1

Blackfin Linux support by http://blackfin.uclinux.org/

Processor Speed: 525 MHz core clock and 131 MHz System Clock

Board Memory: 64MB

Kernel Managed Memory: 64MB

Memory map:

  text      = 0x00001000-0x001d0b60

  rodata    = 0x001d1000-0x00262220

  data      = 0x00263000-0x00284000

    stack   = 0x00264000-0x00266000

  init      = 0x00284000-0x002ac000

  bss       = 0x002ac000-0x002c53c4

  available = 0x002c53c4-0x03dff000

  DMA Zone  = 0x03e00000-0x04000000

NOMPU: setting up cplb tables for global access

Instruction Cache Enabled

Data Cache Enabled (write-through)

Built 1 zonelists.  Total pages: 15748

Kernel command line: root=/dev/nfs rw nfsroot=192.168.1.63:/home/ac/uClinux-dist-2008R1.5-RC3/romfs,tcp,nfsvers=3 console=ttyBF0,57600 console=tty0 ip=192.168.1.64:192.168.1.63:192.168.1.254:255.255.255.0:bf548-ezkit:eth0:off

Configuring Blackfin Priority Driven Interrupts

PID hash table entries: 256 (order: 8, 1024 bytes)

Console: colour dummy device 80x25

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory available: 60064k/65536k RAM, (160k init code, 1854k kernel code, 818k data, 2048k dma, 588k reserved)

Blackfin Scratchpad data SRAM: 4 KB

Blackfin Data A SRAM: 16 KB (15 KB free)

Blackfin Data B SRAM: 16 KB (16 KB free)

Blackfin Instruction SRAM: 48 KB (42 KB free)

Security Framework v1.0.0 initialized

Mount-cache hash table entries: 512

NET: Registered protocol family 16

Blackfin GPIO Controller

Blackfin DMA Controller

ezkit_init(): registering device resources

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

musb_hdrc: version 6.0, musb-dma, host, debug=0

musb_hdrc: kernel must blacklist external hubs

musb_hdrc: USB Host mode controller at ffc03c00 using DMA, IRQ 82

musb_hdrc musb_hdrc.0: MUSB HDRC host driver

musb_hdrc musb_hdrc.0: new USB bus registered, assigned bus number 1

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

dma_alloc_init: dma_page @ 0x03d98000 - 512 pages at 0x03e00000

hub 1-0:1.0: 1 port detected

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

io scheduler noop registered

io scheduler anticipatory registered (default)

io scheduler cfq registered

bf54x-lq043: FrameBuffer initializing...

Console: switching to colour frame buffer device 80x24

bfin-otp: initialized

bfin-wdt: initialized: timeout=20 sec (nowayout=0)

Serial: Blackfin serial driver

bfin-uart.1: ttyBF0 at MMIO 0xffc02000 (irq = 48) is a BFIN-UART

bfin-uart.1: ttyBF1 at MMIO 0xffc03100 (irq = 42) is a BFIN-UART

RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize

smsc911x: Driver version 2007-07-13.

register bfin atapi driver

scsi0 : pata-bf54x

ata1: PATA max UDMA/66 cmd 0x00000000 ctl 0xffc03800 bmdma 0x00000000 irq 68

ata1.00: ATA-7: FUJITSU MHW2040AT, 0000000B, max UDMA/100

ata1.00: 78140160 sectors, multi 16: LBA

ata1.00: configured for UDMA/66

blk_queue_max_hw_segments: set to minimum 1

scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHW2040A 0000 PQ: 0 ANSI: 5

sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

sda: sda1 sda2

sd 0:0:0:0: [sda] Attached SCSI disk

physmap platform flash device: 00400000 at 20000000

physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank

NOR chip too large to fit in mapping. Attempting to cope...

Intel/Sharp Extended Query Table at 0x010A

  Unknown Intel/Sharp Extended Query version 1.5.

gen_probe: No supported Vendor Command Set found

physmap-flash physmap-flash.0: map_probe failed

BF5xx on-chip NAND FLash Controller Driver, Version 1.2 (c) 2007 Analog Devices, Inc.

bf5xx-nand bf5xx-nand.0: page_size=256, data_width=8, wr_dly=3, rd_dly=3

NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit)

Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit":

0x00000000-0x00400000 : "Linux Kernel"

0x00400000-0x10000000 : "File System"

bfin-spi bfin-spi.0: Blackfin BF5xx on-chip SPI Contoller Driver, Version 1.0, regs_base@ffc00500, dma channel@4

bfin-spi bfin-spi.1: Blackfin BF5xx on-chip SPI Contoller Driver, Version 1.0, regs_base@ffc02300, dma channel@5

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

mice: PS/2 mouse device common for all mice

input: bf54x-keys as /class/input/input0

bf54x-keys: Blackfin BF54x Keypad registered IRQ 76

ad7877 spi0.2: touchscreen, irq 123

input: AD7877 Touchscreen as /class/input/input1

rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0

i2c /dev entries driver

i2c-bfin-twi i2c-bfin-twi.1: Blackfin BF5xx on-chip I2C TWI Contoller Driver, Version 1.8, regs_base@ffc02200

usbcore: registered new interface driver usbhid

drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver

Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).

ASoC version 0.13.1

dma rx:0 tx:1, err irq:10, regs:ffc00800

AD1980 SoC Audio Codec

asoc: AC97 <-> bf5xx-ac97 mapping ok

ALSA device list:

  #0: bf5xx-board (AD1980)

TCP cubic registered

NET: Registered protocol family 1

NET: Registered protocol family 17

rtc-bfin rtc-bfin: setting the system clock to 1970-01-01 02:34:58 (9298)

eth0: SMSC911x/921x identified at 0x24000000, IRQ: 175

eth0: SMSC911x MAC Address: 00:e0:22:fe:bd:ed

eth0: link down

IP-Config: Complete:

      device=eth0, addr=192.168.1.64, mask=255.255.255.0, gw=192.168.1.254,

     host=bf548-ezkit, domain=, nis-domain=(none),

     bootserver=192.168.1.63, rootserver=192.168.1.63, rootpath=

Looking up port of RPC 100003/3 on 192.168.1.63

eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

Looking up port of RPC 100005/3 on 192.168.1.63

VFS: Mounted root (nfs filesystem).

Freeing unused kernel memory: 160k freed

Warning: unable to open an initial console.

QuoteReplyEditDelete

 

 

2008-12-18 16:30:12     Re: 548 EZKIT - Booting from vmImage got stuck

Mike Frysinger (UNITED STATES)

Message: 66879   

 

please read the NFS document again.  you skipped the step where it tells you to make sure your /dev is setup.

QuoteReplyEditDelete

 

 

2008-12-18 17:02:11     Re: 548 EZKIT - Booting from vmImage got stuck

AC CHAO (UNITED STATES)

Message: 66881   

 

Hi Mike,

 

I tried to add two nodes in /dev,

 

ac@ac-desktop:~/uClinux-dist-2008R1.5-RC3/romfs/dev$ sudo mknod console c 5 1

ac@ac-desktop:~/uClinux-dist-2008R1.5-RC3/romfs/dev$ sudo mknod null c 1 3

ac@ac-desktop:~/uClinux-dist-2008R1.5-RC3/romfs/dev$ sudo chmod 777 console

ac@ac-desktop:~/uClinux-dist-2008R1.5-RC3/romfs/dev$ sudo chmod 777 null

ac@ac-desktop:~/uClinux-dist-2008R1.5-RC3/romfs/dev$ ls -l

total 0

crwxrwxrwx 1 root root 5, 1 2008-12-18 13:47 console

crwxrwxrwx 1 root root 1, 3 2008-12-18 13:48 null

 

Now I can see the previous error is disappeared.

 

But I saw several errors have "resampling too fast" on the EKIT's LCD console.

 

Could you advise how to add all needed devices in /dev correctly?

 

Thank you.

 

Regards,

 

AC

QuoteReplyEditDelete

 

 

2008-12-18 17:58:53     Re: 548 EZKIT - Booting from vmImage got stuck

Mike Frysinger (UNITED STATES)

Message: 66883   

 

i have never seen "resampling too fast" so i dont know what that is

QuoteReplyEditDelete

 

 

2008-12-19 00:46:22     Re: 548 EZKIT - Booting from vmImage got stuck

AC CHAO (UNITED STATES)

Message: 66888   

 

Hi Mike,

 

 

 

Sorry, I overlooked.

 

The error messgae shown on LCD screen should be

 

init: -/bin/sh respawning too fast

 

init: /bin/watchdogd respawning too fast

 

init: /sbin/syslogd respawning too fast

 

then repeated these three messages again and again.

 

 

 

I have another question,

 

My PC only can get the console message

 

..............

 

VFS: Mounted root (nfs filesystem).

Freeing unused kernel memory: 160k freed

 

 

After the above message, there is no more message.

 

 

 

 

 

But the EZKIT's LCD screen can show the complete boot up message and I can see "Have a lot of fun..."

 

 

 

Do you know what I am missing? Thank you.

 

 

 

Regards,

 

 

 

AC

QuoteReplyEditDelete

 

 

2008-12-19 00:56:44     Re: 548 EZKIT - Booting from vmImage got stuck

Mike Frysinger (UNITED STATES)

Message: 66890   

 

console= order matters

 

your /dev probably still isnt populated with device nodes, and your / is read only so mdev doesnt create them for you

QuoteReplyEditDelete

 

 

2008-12-19 01:32:58     Re: 548 EZKIT - Booting from vmImage got stuck

AC CHAO (UNITED STATES)

Message: 66892   

 

Hi Mike,

 

 

 

Thanks a lot for immediate reply. It's midnight for you. Please have a nice rest.

 

I changed the read/write permission by the following command

 

ac@ac-desktop:~/uClinux-dist-2008R1.5-RC3$sudo chmod -R 777 romfs

 

ac@ac-desktop:~/uClinux-dist-2008R1.5-RC3$sudo chmod 777 /

 

But the same error messages were shown.

 

Did I do the right step to change the "/" read/write permission?

 

Thank you.

 

 

 

Regards,

 

 

 

AC

QuoteReplyEditDelete

 

 

2008-12-19 02:11:38     Re: 548 EZKIT - Booting from vmImage got stuck

AC CHAO (UNITED STATES)

Message: 66894   

 

Hi Mike,

 

 

 

I just checked the console on EZKIT's LCD screen,

 

when I use shell command "ls -l", I saw "." and ".." both are drwxrwxrwx.

 

But if use "chmod 777 /", I saw "chmod: /: Read-only file system".

 

Do you know where could be the problem?

 

If you need any more info, please let me know.

 

Thanks.

 

 

 

Regards,

 

 

 

AC

 

 

QuoteReplyEditDelete

 

 

2008-12-19 02:55:36     Re: 548 EZKIT - Booting from vmImage got stuck

Mike Frysinger (UNITED STATES)

Message: 66899   

 

check your nfs server permissions and try mounting it locally

 

btw, you most certainly do not want 777 on your development / ...

QuoteReplyEditDelete

 

 

2008-12-19 11:09:57     Re: 548 EZKIT - Booting from vmImage got stuck

AC CHAO (UNITED STATES)

Message: 66956   

 

Hi Mike,

 

 

 

Thanks a lot. You are right. The permission is read-only when I tried locally. After correting this problem, there is no "respawning too fast" error.

 

The console message on the EZKIT's LCD screen is normal, but the console message receievd by my PC only has the following message. Do you know why it stopped communicate with my PC?

 

Thanks.

 

 

 

Regards,

 

 

 

AC

 

 

U-Boot 1.1.6-svn1273 (ADI-2008R1.5) (Jul 21 2008 - 00:35:28)

 

CPU:   ADSP bf548-0.0 (Detected Rev: 0.1)

Board: ADI BF548 EZ-Kit board

       Support: http://blackfin.uclinux.org/

Clock: VCO: 525 MHz, Core: 525 MHz, System: 131 MHz

RAM:   64 MB

Flash: 16 MB

NAND:  256 MiB

In:    serial

Out:   serial

Err:   serial

Net:   LAN9x18 (0x118a0000) detected at 0x24000000

MAC:   00:E0:22:FE:BD:ED

Hit any key to stop autoboot:  0

start Auto negotiation... (take ~2sec)

Auto negotiation complete, 100BaseTX, full duplex

TFTP from server 192.168.1.63; our IP address is 192.168.1.64

Filename 'vmImage'.

Load address: 0x1000000

Loading: #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     ######################################################

done

Bytes transferred = 12589535 (c019df hex)

## Booting image at 01000000 ...

   Image Name:   Linux-2.6.22.19-ADI-2008R1.5-svn

   Created:      2008-12-19  15:48:54 UTC

   Image Type:   Blackfin Linux Kernel Image (gzip compressed)

   Data Size:    12589471 Bytes = 12 MB

   Load Address: 00001000

   Entry Point:  00284000

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK

Starting Kernel at = 284000

Linux version 2.6.22.19-ADI-2008R1.5-svn (ac@ac-desktop) (gcc version 4.1.2 (ADI svn)) #141 Fri Dec 19 07:48:49 PST 2008

Hardware Trace Active and Enabled

Blackfin support (C) 2004-2007 Analog Devices, Inc.

Compiled for ADSP-BF548 Rev 0.0

Warning: Compiled for Rev 0, but running on Rev 1

Blackfin Linux support by http://blackfin.uclinux.org/

Processor Speed: 525 MHz core clock and 131 MHz System Clock

Board Memory: 64MB

Kernel Managed Memory: 64MB

Memory map:

  text      = 0x00001000-0x001d0b60

  rodata    = 0x001d1000-0x00262220

  data      = 0x00263000-0x00284000

    stack   = 0x00264000-0x00266000

  init      = 0x00284000-0x0167a000

  bss       = 0x0167a000-0x016933c4

  available = 0x016933c4-0x03dff000

  DMA Zone  = 0x03e00000-0x04000000

NOMPU: setting up cplb tables for global access

Instruction Cache Enabled

Data Cache Enabled (write-through)

Built 1 zonelists.  Total pages: 15748

Kernel command line: console=ttyBF0,57600 root=/dev/nfs rw nfsroot=192.168.1.63:/home/ac/workdir/filesys,tcp,nfsvers=3 console=tty0 ip=192.168.1.64:192.168.1.63:192.168.1.254:255.255.255.0:bf548-ezkit:eth0:off

Configuring Blackfin Priority Driven Interrupts

PID hash table entries: 256 (order: 8, 1024 bytes)

Console: colour dummy device 80x25

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory available: 39784k/65536k RAM, (20440k init code, 1854k kernel code, 818k data, 2048k dma, 588k reserved)

Blackfin Scratchpad data SRAM: 4 KB

Blackfin Data A SRAM: 16 KB (15 KB free)

Blackfin Data B SRAM: 16 KB (16 KB free)

Blackfin Instruction SRAM: 48 KB (42 KB free)

Security Framework v1.0.0 initialized

Mount-cache hash table entries: 512

NET: Registered protocol family 16

Blackfin GPIO Controller

Blackfin DMA Controller

ezkit_init(): registering device resources

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

musb_hdrc: version 6.0, musb-dma, host, debug=0

musb_hdrc: kernel must blacklist external hubs

musb_hdrc: USB Host mode controller at ffc03c00 using DMA, IRQ 82

musb_hdrc musb_hdrc.0: MUSB HDRC host driver

musb_hdrc musb_hdrc.0: new USB bus registered, assigned bus number 1

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

dma_alloc_init: dma_page @ 0x03db0000 - 512 pages at 0x03e00000

hub 1-0:1.0: 1 port detected

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

io scheduler noop registered

io scheduler anticipatory registered (default)

io scheduler cfq registered

bf54x-lq043: FrameBuffer initializing...

Console: switching to colour frame buffer device 80x24

bfin-otp: initialized

bfin-wdt: initialized: timeout=20 sec (nowayout=0)

Serial: Blackfin serial driver

bfin-uart.1: ttyBF0 at MMIO 0xffc02000 (irq = 48) is a BFIN-UART

bfin-uart.1: ttyBF1 at MMIO 0xffc03100 (irq = 42) is a BFIN-UART

RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize

smsc911x: Driver version 2007-07-13.

register bfin atapi driver

scsi0 : pata-bf54x

ata1: PATA max UDMA/66 cmd 0x00000000 ctl 0xffc03800 bmdma 0x00000000 irq 68

ata1.00: ATA-7: FUJITSU MHW2040AT, 0000000B, max UDMA/100

ata1.00: 78140160 sectors, multi 16: LBA

ata1.00: configured for UDMA/66

blk_queue_max_hw_segments: set to minimum 1

scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHW2040A 0000 PQ: 0 ANSI: 5

sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

sda: sda1 sda2

sd 0:0:0:0: [sda] Attached SCSI disk

physmap platform flash device: 00400000 at 20000000

physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank

NOR chip too large to fit in mapping. Attempting to cope...

Intel/Sharp Extended Query Table at 0x010A

  Unknown Intel/Sharp Extended Query version 1.5.

gen_probe: No supported Vendor Command Set found

physmap-flash physmap-flash.0: map_probe failed

BF5xx on-chip NAND FLash Controller Driver, Version 1.2 (c) 2007 Analog Devices, Inc.

bf5xx-nand bf5xx-nand.0: page_size=256, data_width=8, wr_dly=3, rd_dly=3

NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V 8-bit)

Creating 2 MTD partitions on "NAND 256MiB 3,3V 8-bit":

0x00000000-0x00400000 : "Linux Kernel"

0x00400000-0x10000000 : "File System"

bfin-spi bfin-spi.0: Blackfin BF5xx on-chip SPI Contoller Driver, Version 1.0, regs_base@ffc00500, dma channel@4

bfin-spi bfin-spi.1: Blackfin BF5xx on-chip SPI Contoller Driver, Version 1.0, regs_base@ffc02300, dma channel@5

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

mice: PS/2 mouse device common for all mice

input: bf54x-keys as /class/input/input0

bf54x-keys: Blackfin BF54x Keypad registered IRQ 76

ad7877 spi0.2: touchscreen, irq 123

input: AD7877 Touchscreen as /class/input/input1

rtc-bfin rtc-bfin: rtc core: registered rtc-bfin as rtc0

i2c /dev entries driver

i2c-bfin-twi i2c-bfin-twi.1: Blackfin BF5xx on-chip I2C TWI Contoller Driver, Version 1.8, regs_base@ffc02200

usbcore: registered new interface driver usbhid

drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver

Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).

ASoC version 0.13.1

dma rx:0 tx:1, err irq:10, regs:ffc00800

AD1980 SoC Audio Codec

asoc: AC97 <-> bf5xx-ac97 mapping ok

ALSA device list:

  #0: bf5xx-board (AD1980)

TCP cubic registered

NET: Registered protocol family 1

NET: Registered protocol family 17

rtc-bfin rtc-bfin: setting the system clock to 1970-01-01 00:33:56 (2036)

eth0: SMSC911x/921x identified at 0x24000000, IRQ: 175

eth0: SMSC911x MAC Address: 00:e0:22:fe:bd:ed

eth0: link down

IP-Config: Complete:

      device=eth0, addr=192.168.1.64, mask=255.255.255.0, gw=192.168.1.254,

     host=bf548-ezkit, domain=, nis-domain=(none),

     bootserver=192.168.1.63, rootserver=192.168.1.63, rootpath=

Freeing unused kernel memory: 20440k freed

eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

 

QuoteReplyEditDelete

 

 

2008-12-19 13:27:10     Re: 548 EZKIT - Booting from vmImage got stuck

Mike Frysinger (UNITED STATES)

Message: 66959   

 

like i said, console= order matters.  last one gets preference.

QuoteReplyEditDelete

 

 

2008-12-19 17:45:29     Re: 548 EZKIT - Booting from vmImage got stuck

AC CHAO (UNITED STATES)

Message: 66970   

 

Hi Mike,

 

Thanks a lot. Do you know why?

 

Regards,

 

AC

QuoteReplyEditDelete

 

 

2008-12-19 18:08:57     Re: 548 EZKIT - Booting from vmImage got stuck

Mike Frysinger (UNITED STATES)

Message: 66971   

 

something needs preference

 

QuoteReplyEditDelete

 

 

2008-12-19 18:30:11     Re: 548 EZKIT - Booting from vmImage got stuck

AC CHAO (UNITED STATES)

Message: 66972   

 

Hi Mike,

 

Thank you. I will feed Linux its best wish.

 

Regards,

 

AC

Attachments

    Outcomes