Q In this case, I have to use ad7708 confidured as 315Hz to achive 20Hz reading for each channel in chop disable mode. But I have a doubt that, I'll confugure it as 315Hz o/p rate but will read it as 100Hz. If so how peak-to-peak resolution will change. It will be seen according to 315Hz o/p rate or 100Hz? Smilarly, which one of these data output rate defines digital filter response, 315Hz or 100Hz? And how can I calculate resolution bit according to data output rate and PGA(programmable gain amplifier). Is there any formula to find it? A When you change channels the first o/p is automatically delayed….the 2nd and subsequent o/p’s will be at the programmed rate, provided you do not change channels. The pp resolution will be as defined in the programmed o/p rate..in this case 315Hz. CHOP at 105Hz To re-cap, when you program the device for chop mode, with SF = 13, the digital filter needs 3 samples taking a time of 3.1msec for each filter o/p. In chop mode, you take 2 results from the digital filter to give one o/p. This gives a total of 19msec for the first result and 9.3msec for each subsequent result.. ( 2nd sample uses the 2nd o/p of the digital filter as it’s first o/p). Resulting in an o/p rate of 52.5 for the first sample and 105Hz for every subsequent sample. NON-Chop at 315Hz In non-chop mode, with SF= 13, again the digital filter needs 3 samples to process the first o/p , i.e 9.3mec, however each subsequent o/p is available 3.1msec later as the digital filter uses 2 of the three previous samples to process the 2nd result. Giving an update rate of 105Hz for the first result and 315 for every subsequent result, again provided you do not change channels. If you change channels continuously, then the update rate is 105Hz. The accuracy will of couse be for the programmed update rate, i.e non-chop at 315Hz, o/p reduced to 105Hz when switching each sample, o/p accuracy conforms to 315Hz.

What precautions, if any, should I take to use external clock source instead of crystal/resonator?

Q What precautions, if any, should I take to use external clock source instead of crystal/resonator? A You can apply a 32768 Hz oscillator signal to the XTAL1 pin - see the input specifications on page 5 of the datasheet. The PLL should be able to lock onto that and generate the 4.19MHz clock. The jitter of the clock source is not important, since any jitter will be averaged out by the decimation performed in the sigma delta and post filtering. However, the absolute accuracy and temperature drift of the clock source is important since the output update rate and placement of filter notches is a direct function of the clock frequency.

English

Forums
Popular Forums
Product Forums
View All
Application Forums
Design Center Forums
Learn
Highlighted Webinar

COTS SoMs & Phased Array Solutions for Rapid RF Subsystem Integration
Accelerate RF Subsystem Integration with COTS SoMs and Phased Array Solutions. As building a subsystem from early prototype to full deployment is never...
Places
Libraries
Upcoming Learning & Events
- Humanoid Robotics: Deterministic Motion Control & Edge AI Systems
- Power Integrity for High Performance Measurement Systems
View All Webinars
Community Hub
Challenge Yourself!
View All
What's Brewing
View All
Places
Resources
View All
ContentZone
Visit ContentZone
Search content by industry or technology.

Blogs

Technical Articles

Tutorials

Videos

Webinars

Your ADI content all in one place.
View ContentZone
The Latest Read

JESD204 Bring-Up: From Link-Up to Data Integrity
This blog presents a structured bring-up methodology for the ZCU102 + ADRV9009 platform, stepping through each initialization phase in sequence and identifying...

New Release

Signal Chain Designer: DC Error Simulation
This video covers the DC error calculation capabilities of Signal Chain Designer. DC error is unique in that often requires calibration and has so many...

Recent Technical Insights

Calibration Implementation Techniques for Multichannel Phased Array Subsystems
Learn about phase-calibration techniques used for characterizing a 16 transmit and 16 receive X-band phased array subsystem based on a mixed-signal front...

EngineerZone

Precision ADCs

Log In

User
Site
Search

OR

Ask a Question

Data Converters

Precision ADCs

Documents AD7708: FAQ

Q&A
File Uploads
FAQs/Docs
Help Articles
Members
Tags
Cancel

Products Mentioned

AD7708 Production
The AD7708 / AD7718Â are complete analog front-ends for low frequency measurement applications. The AD7718 contains a 24-bit sigma delta ADC with PGA and...
Datasheet
AD7708 on Analog.com

Table of Contents

+Documents
+General: FAQ
+AD1139: FAQ
+AD7091R Conversion Result Change
+AD1556: FAQ
+AD1580: FAQ
+AD1582: FAQ
+AD2S1200: FAQ
+AD2S1205: FAQ
+AD2S1210: FAQ
+AD2S75: FAQ
+AD2S80: FAQ
+AD2S80A: FAQ
+AD2S82A: FAQ
+AD2S83: FAQ
+AD2S90: FAQ
+AD2S99: FAQ
+AD4110-1: FAQ
+AD411x: FAQ
+AD5940: FAQ
+AD598: FAQ
+AD650: FAQ
+AD652: FAQ
+AD654: FAQ
+AD7091: FAQ
+AD7091R-X: FAQ
+AD711: FAQ
+AD7124-4: FAQ
+AD7124-8: FAQ
+AD7134: FAQ
+AD713: FAQ
+AD7142: FAQ
+AD7147: FAQ
+AD7148: FAQ
+AD7150: FAQ
+AD7151: FAQ
+AD7175-2: FAQ
+AD7176-2: FAQ
+AD7176: FAQ
+AD717x: FAQ
+AD7190: FAQ
+AD7192: FAQ
+AD7193: FAQ
+AD7195: FAQ
+AD719x: FAQ
+AD7265: FAQ
+AD7266: FAQ
+AD7280: FAQ
+AD7291: FAQ
+AD7298: FAQ
+AD7305: FAQ
+AD7321: FAQ
+AD7323: FAQ
+AD7328: FAQ
+AD7366-5: FAQ
+AD7367: FAQ
+AD736ARZ: FAQ
+AD737: FAQ
+AD738x : FAQ
+AD7398: FAQ
+AD7400A: FAQ
+AD7401: FAQ
+AD7403: FAQ
+AD74111: FAQ
+AD7415: FAQ
+AD7416: FAQ
+AD7417: FAQ
+AD7418: FAQ
+AD7450: FAQ
+AD7475: FAQ
+AD7484: FAQ
+AD7490: FAQ
+AD7492: FAQ
+AD75019: FAQ
+AD7503: FAQ
+AD7541A: FAQ
+AD7546: FAQ
AD7547: FAQ
+AD7568: FAQ
+AD7578: FAQ
+AD7606-4: FAQ
+AD7606: FAQ
+AD7606B: FAQ
+AD7606C: FAQ
+AD7608: FAQ
+AD7616 FAQ
+AD7616-P: FAQ
+AD7621: FAQ
+AD7625: FAQ
+AD7626: FAQ
+AD7631: FAQ
+AD7653: FAQ
+AD7654: FAQ
+AD7655: FAQ
+AD7656: FAQ
+AD7657-1: FAQ
+AD7663: FAQ
+AD7674: FAQ
+AD7675: FAQ
+AD7678: FAQ
+AD7682: FAQ
+AD7683: FAQ
+AD7684: FAQ
+AD7685: FAQ
+AD7688: FAQ
+AD7689: FAQ
+AD7690: FAQ
+AD7691: FAQ
+AD7705: FAQ
+AD7706: FAQ
+AD7707: FAQ
-AD7708: FAQ
- What precautions, if any, should I take to use external clock source instead of crystal/resonator?
- AD7708: Update rate
+AD7709: FAQ
+AD7710: FAQ
+AD7711A: FAQ
+AD7712: FAQ
+AD7713: FAQ
+AD7714: FAQ
+AD7714YN: FAQ
+AD7715: FAQ
+AD7716: FAQ
+AD7718: FAQ
+AD7719: FAQ
+AD7720: FAQ
+AD7722: FAQ
+AD7725: FAQ
+AD7730: FAQ
+AD7731: FAQ
+AD7732: FAQ
+AD7738: FAQ
+AD7740: FAQ
+AD7741: FAQ
+AD7745: FAQ
+AD7746: FAQ
+AD7747: FAQ
+AD7760: FAQ
+AD7763: FAQ
+AD7766: FAQ
+AD7768: FAQ
+AD777x: FAQ
+AD7780: FAQ
+AD7785: FAQ
+AD7787: FAQ
+AD7788: FAQ
+AD7790: FAQ
+AD7792: FAQ
+AD7793: FAQ
+AD7794: FAQ
+AD7795: FAQ
+AD7798: FAQ
+AD7799: FAQ
+AD7805: FAQ
+AD7808: FAQ
+AD7809: FAQ
+AD780: FAQ
+AD7811: FAQ
+AD7812: FAQ
+AD7817: FAQ
+AD7819: FAQ
+AD7821: FAQ
+AD7825: FAQ
+AD7829: FAQ
+AD7835: FAQ
+AD7849: FAQ
+AD7851: FAQ
+AD7854: FAQ
+AD7856: FAQ
+AD7858: FAQ
+AD7859: FAQ
+AD7864: FAQ
+AD7865 : FAQ
+AD7872: FAQ
+AD7874: FAQ
+AD7879: FAQ
+AD7887: FAQ
+AD7888: FAQ
+AD7891-1: FAQ
+AD7891: FAQ
+AD7893-2: FAQ
+AD7895: FAQ
+AD7896: FAQ
+AD7899: FAQ
+AD7912: FAQ
+AD7921: FAQ
+AD7924: FAQ
+AD7927: FAQ
+AD7938: FAQ
+AD7942: FAQ
+AD7949: FAQ
+AD7960: FAQ
+AD7961: FAQ
+AD797: FAQ
+AD7980: FAQ
+AD7982: FAQ
+AD7984: FAQ
+AD7986: FAQ
+AD7988-1: FAQ
+AD7993: FAQ
+AD7994: FAQ
+AD7997: FAQ
+AD7998: FAQ
+ADA2200: FAQ
+ADAS1000: FAQ
+ADAS3022: FAQ
+ADAS3023: FAQ
+ADC: FAQ
+ADVFC32: FAQ
+EVAL-AD7719-EB: FAQ
+EVAL-ADAS3022EDZ: FAQ
+RDC1740: FAQ
+AD4030-24: FAQ
+AD4114: FAQ
+AD4116: FAQ
+AD4130-8 FAQ
+AD4131-8: FAQ
+AD4134 FAQ
+AD4170: FAQ
+AD4858
+AD674BBD: FAQ
+AD7172-2: FAQ
+AD7175-8: FAQ
+AD7191: FAQ
AD73360: FAQ
+AD73360AR: FAQ
+AD73360L: FAQ
+AD7357: FAQ
+AD7386-4: FAQ
+AD738x-4: FAQ
AD7398 SPI Voltage vs VCC
+AD7457: FAQ
+AD7606C-16: FAQ
+AD7609: FAQ
+AD7656-1: FAQ
AD7660: FAQ
+AD7665: FAQ
+AD7680: FAQ
+AD7686: FAQ
+AD7764: FAQ
+AD7778: FAQ
AD7892: FAQ
+AD7980SRMZ-EP: FAQ
+AD7991: FAQ
+AD9243: FAQ
+AD9260: FAQ
+AD9261: FAQ
+AD9262: FAQ
+AD974: FAQ
+AD976A: FAQ
+AD977A: FAQ
+ADAQ4003: FAQ
+ADAQ7768-1: FAQ
+ADAQ8092 FAQ
+DC590, DC2026, QuikEval: FAQs
+EVAL-AD7768-4FMCZ: FAQ
+Legacy LTC - Sigma Delta ADCs FAQ
+LTC2408: FAQ
+LTC2497: FAQ
+MAX1028: FAQ
+MAX1036: FAQ
+MAX1037EKA+: FAQ
+MAX11040GUU+: FAQ
+MAX11043: FAQ
+MAX11045: FAQ
+MAX11046 16-BIT AD: FAQ
+MAX11048: FAQ
+MAX11100EUB+: FAQ
+MAX11101: FAQ
+MAX11103: FAQ
+MAX11108: FAQ
MAX11125: FAQ
+MAX11125ATI+: FAQ
+MAX11130: FAQ
+MAX11131ATI+: FAQ
+MAX11136ATI+: FAQ
+MAX11150EVKIT#: FAQ
+MAX11154: FAQ
MAX11156: FAQ
+MAX11156ETC+: FAQ
+MAX11158: FAQ
+MAX11163: FAQ
+MAX11168EUB+: FAQ
+MAX11169EUB+: FAQ
+MAX11190: FAQ
+MAX11190ATE+: FAQ
MAX11192: FAQ
+MAX11192EVKIT#: FAQ
+MAX11200: FAQ
+MAX11200EEE+: FAQ
+MAX11201: FAQ
+MAX11203EEE+: FAQ
+MAX11206: FAQ
+MAX11207EEE+: FAQ
MAX11210: FAQ
+MAX11210EEE+: FAQ
+MAX11213EEE+T: FAQ
MAX11214: FAQ
MAX11214EUG+: FAQ
+MAX11214EUG+_T1: FAQ
+MAX11216: FAQ
+MAX11254ATJ+: FAQ
+MAX11254EVKIT#: FAQ
+MAX11259AWX+T: FAQ
+MAX11259PMB#: FAQ
+MAX11261BOB#: FAQ
+MAX11261ENX+: FAQ
+MAX11270EUG+: FAQ
+MAX11337ATJ+: FAQ
+MAX11410ATI+: FAQ
+MAX11608: FAQ
+MAX11609EEE+: FAQ
+MAX11612EUA+: FAQ
+MAX11612EVSYS: FAQ
+MAX11614EEE+: FAQ
+MAX11615EEE+C78: FAQ
+MAX11615EWE+: FAQ
+MAX11616EEE+: FAQ
+MAX11617EWE+: FAQ
+MAX11625: FAQ
+MAX11629EEE+: FAQ
+MAX11645EWC+T: FAQ
+MAX11647EUA+: FAQ
+MAX11900: FAQ
MAX11905: FAQ
+MAX11905EVKIT#: FAQ
+MAX1202AEAP+: FAQ
+MAX1220: FAQ
+MAX1229: FAQ
+MAX1230BCEG+: FAQ
+MAX1231AEEG+: FAQ
+MAX1239EEE+: FAQ
+MAX1239KEEE+: FAQ
+MAX1239LEEE+: FAQ
+MAX1258: FAQ
+MAX1271ACNG+: FAQ
MAX1300: FAQ
+MAX1300BEUG+: FAQ
+MAX1301AEUP+: FAQ
+MAX13171: FAQ
+MAX13204EALT+: FAQ
MAX1343: FAQ
+MAX1343BETX+: FAQ
+MAX13487: FAQ
+MAX13488: FAQ
+MAX1379ATP+: FAQ
+MAX1383: FAQ
+MAX1447ECJ+: FAQ
MAX14571: FAQ
+MAX14571EUD+: FAQ
MAX14574EWL+: FAQ
+MAX14574EWL+T: FAQ
+MAX14578: FAQ
+MAX14579EEVKIT#: FAQ
+MAX14588ETE+T: FAQ
+MAX145ACPA+: FAQ
+MAX1474: FAQ
+MAX14783: FAQ
+MAX14805: FAQ
+MAX14807ECB+: FAQ
+MAX14900D: FAQ
+MAX15090BEWI+: FAQ
+MAX1645AEEI+: FAQ
+MAX16600GGN+: FAQ
+MAX17823AGCB+: FAQ
MAX17823AGCB/V+: FAQ
+MAX17823AGCB/V+T: FAQ
+MAX17823GCB+: FAQ
+MAX182BEWI+T: FAQ
+MAX19777AZA+: FAQ
+MAX31865: FAQ
+MAX31865AAP+: FAQ
+Precision Technology Learning Modules
Programming FMC FRU ID EEPROM on Linux