Analog.com
Analog
Dialogue
Wiki
简体中文
EngineerZone
Search
Log in
Site
Search
Log in
Home
Blogs ⌵
Analog Garage
EngineerZone Spotlight
The Engineering Mind
Browse ⌵
All Groups
All Members
Support ⌵
Amplifiers
Analog Microcontrollers
Audio
Clock and Timing
Data Converters
Design Tools and Calculators
Direct Digital Synthesis (DDS)
Embedded Vision Sensing
Energy Monitoring and Metering
FPGA Reference Designs
Interface and Isolation
Low Power RF Transceivers
MEMS Inertial Sensors
Motor Control Hardware Platforms
Optical Sensing
Power By Linear
Processors and DSP
Reference Circuits
RF and Microwave
Switches/Multiplexers
Temperature Sensors
Video
Wireless Sensor Networks
More
Cancel
Data Converters
More
High-Speed DACs
Documents
Documents
Q&A
Discussions
Documents
File Uploads
Video/Images
Tags
Reports
More
Cancel
New
High-Speed DACs requires membership for participation - click to join
-
Documents
TAGS LIST: High-Speed DACs
AD9115: Limit for the current the part can deliver
AD9116_power supply
AD9117: How do I estimate the overall DAC pipeline delay?
AD9122-M5375-EBZ Harmonics at 90MHz
AD9129 - Compatible data generator ad9129
AD9129 - Highest RF output frequency spectrum supported
AD9129 - Mix-Mode function
AD9129 - Clock source and buffer recommendation
AD9129 datasheet clarifications
AD9135/AD9136 - Are there evaluation boards available?
AD9135/AD9136 - Does the AD9135/AD9136 support deterministic latency/multi-chip synchronization?
AD9135/AD9136 - How do I select between the two parts?
AD9135/AD9136 - What are the key specifications for my application?
AD9135/AD9136 - What is the max data rate the AD9135/AD9136 supports?
AD9142A Byte Interface Mode
AD9142A: error message when setting up offsets ( IDAC/QDAC, IQ phase& Gain ADJ )
AD9144 - Does the AD9144 support deterministic latency/multi-chip synchronization?
AD9144 - Is this a JESD204B SERDES high-speed DAC product?
AD9144 - What evaluation boards are available?
AD9144 - What is the difference between the DPG3 compatible boards and the FMC evaluation board?
AD9144 - What JESD204B SERDES modes are available on the AD9144?
AD9148: Unused channel / Unused pins
AD9712 general recommendations
AD9716 - Logic Levels at AVDD=3.3V, DVDD=1.8V, DVDDIO=1.8V, CVDD=1.8V
AD9717: Pin connection
AD9726: Interface with the AD600
AD9726_Iout equation error
AD9734: multichip SYNCHRONIZATION
AD9734: Synchronize two DACs
AD9736 - Theta JC
AD9739: FPGA selection
AD9739: IRQ clearance
AD9739: May I leave SYNC_OUT and SYNC_IN pins unconnected?
AD9739: multichip synchronization
AD9739: Output amplitude DC-offset
AD9739A-FMC-EBZ with Zedboard
AD9739_AC coupling LVDS
AD9739_balun two sides
AD9739_CLK input model and little output power
AD9739_R2-EBZ DAC Output stage termination
AD9742/AD9744 Exposed Pad
AD9742_several questions_DCOM and ACOM
AD9742_several questions_differential resistor
AD9744: Maximum sample rate
AD9747: Thermal Information
AD9748_REFLO pin
AD974: Antialiasing filter
AD9765 influence of the clocks
AD9767: Input timing for interleaved mode
AD9767: Load range
AD976A's Transfer function
AD977 ?jb
AD9774: CLK input voltage
AD9774: DAC output range and external buffer
AD9776: Maximum sample rate
AD9777 / AD9779: The two channel DACs, can they be used separately?
AD9777 max speed and timing query (SR#: 1200982)
AD9777: DATACLK can only be output pin
AD9777: Modulating the bandwidth
AD9779: Grounding and layout recommendation
AD977A: Driving the inputs
AD977A: is it possible to use one AD780 to be the ref voltage of 16 AD977A for +-10V range?
AD9780 driven by FMC Board Clock
AD9783: LVDS interface termination resistor
AD9783: read back value of the Hardware Version of the AD9783
AD9786: Current output voltage calculation
AD9786: Propagation delay
AD9786: Reset timing
AD9786: Thermal pad connection
AD9788: Can I bypass the NCO (numerically controlled oscillators)?
AD9789: AD9789EBZ and AD9789-Mix-EBZ difference
Alias Frequencies
Can AD9763's NC pins (i.e. pin 33 & 34) be driven or must they be definitely left floating?
Can fs/4 spurs be reduced or eliminated by factory calibration, or any other method, on the AD9739/AD9739A?
DAC AD9122 and AD-FMCJESDADC1-EBZ wrt external trigger
DAC REFOUT Current
Datasheet errors in the AD9736/5/4
Digital Pattern Generator?
Driving the clock of AD9739 DAC
Evalboards use DAC "N" output and the datasheet uses the DAC "P" output. Which is correct?
FAQ: What is the latency of the AD9739?
FAQ: What is the latency of the AD9789?
High-speed ADC for non-uniform sampling
HIGH-SPEED DAC SUPPORT COMMUNITY
How accurate is the AD9739's output impedance of 70ohms?
Impedance matching when AD9717 or AD9779A interfaced with ADL5375
Output pins
Should I connect to ground the CMLI, CMLQ, FSADJI and FSADJQ pins?
Some soldered jumpers on the AD9122 Evalboard are not as per default settings mentioned in User Guide
The AD9146 Filters, Premodulator and modes?
What is the difference between the DPG3 compatible boards and the FMC evaluation board?
What is the highest RF output frequency supported by the AD9144?
What is the latency of the AD9777,5,3 DAC family?
What is the max data rate the AD9144 supports?
What is the Psi-jt for the AD9142A package (72-pin LFCSP)?
What is the tuning resolution of the output frequency of these devices?
What JESD204B SERDES modes are available on the AD9135/AD9136?
Where can I find the BOM, schematics and gerbers for AD9119-MIX-EBZ?
Why do I see a very large signal at 2*fdac for the AD9739 DAC?
Documents
Share
History
More
Cancel