QPLL TX buffer underflow error, status: 0x61

nirbhay100

on Feb 24, 2024

Category: Hardware

Product Number: AD9081

Hi,

I am using AD9081 EVM running with Xilinx KCU105(Kintex ultrascale FPGA). Design is migrated from analog device provided HDL and no-os driver for VCU118. After loading the elf file, I am getting the QPLL TX buffer underflow error, status: 0x61 on serial port.

Log file for the serial port is attached.

Kindly suggest the changes to come out this issue.

Hello
rx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:527:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer underflow error, status: 0x61
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:534:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer overflow error, status: 0x61
ad9081_jesd_rx_link_status_print: JESD TX (JRX) Link1 0x0 lanes in DATA
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:527:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer underflow error, status: 0x61
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:534:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer overflow error, status: 0x61
ad9081_jesd_rx_link_status_print: JESD TX (JRX) Link1 0x0 lanes in DATA
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:527:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer underflow error, status: 0x61
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:534:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer overflow error, status: 0x61
ad9081_jesd_rx_link_status_print: JESD TX (JRX) Link1 0x0 lanes in DATA
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:527:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer underflow error, status: 0x61
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:534:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer overflow error, status: 0x61
ad9081_jesd_rx_link_status_print: JESD TX (JRX) Link1 0x0 lanes in DATA
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:527:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer underflow error, status: 0x61
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:534:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer overflow error, status: 0x61
ad9081_jesd_rx_link_status_print: JESD TX (JRX) Link1 0x0 lanes in DATA
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:527:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer underflow error, status: 0x61
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:534:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer overflow error, status: 0x61
ad9081_jesd_rx_link_status_print: JESD TX (JRX) Link1 0x0 lanes in DATA
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:527:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer underflow error, status: 0x61
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:534:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer overflow error, status: 0x61
ad9081_jesd_tx_link_status_print: JESD RX (JTX) Link1 in DATA, SYNC deasserted, PLL locked, PHASE established, MODE valid
DAC IRQ status 0xf043000000
IRQ_STATUS0: 0x0
ad9081_multichip_sync:2
ad9081_multichip_sync:3
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:527:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer underflow error, status: 0x61
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:534:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer overflow error, status: 0x61
ad9081_jesd_rx_link_status_print: JESD TX (JRX) Link1 0x0 lanes in DATA
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:527:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer underflow error, status: 0x61
ERR: ../noos/drivers/axi_core/jesd204/axi_adxcvr.c:534:adxcvr_clk_enable(): adxcvr_clk_enable: QPLL TX buffer overflow error, status: 0x61
ad9081_jesd_rx_link_status_print: JESD TX (JRX) Link1 0x0 lanes in DATA
AD9081 Rev. 3 Grade 10 (API 1.2.2) probed
tx_jesd status:
        Link is enabled
        Measured Link Clock: 249.998 MHz
        Reported Link Clock: 250.000 MHz
        Lane rate: 10000.000 MHz
        Lane rate / 40: 250.000 MHz
        LMFC rate: 7.812 MHz
        SYNC~: asserted
        Link status: CGS
        SYSREF captured: Yes
        SYSREF alignment error: No
rx_jesd status:
        Link is enabled
        Measured Link Clock: 249.998 MHz
        Reported Link Clock: 250.000 MHz
        Lane rate: 10000.000 MHz
        Lane rate / 40: 250.000 MHz
        LMFC rate: 7.812 MHz
        Link status: CGS
        SYSREF captured: Yes
        SYSREF alignment error: No
tx_dac: Successfully initialized (249996948 Hz)
rx_adc: Successfully initialized (249996948 Hz)
Running TinyIIOD server...
                          If successful, you may connect an IIO client application by:
                                                                                      1. Disconnecting the serial terminal you use to view this message.
                                                                                                                                                        2. Connecting the IIO client application using the serial backend configured as shown:
        Baudrate: 115200
                                Data size: 8 bits
                                                        Parity: none
                                                                        Stop bits: 1
                                                                                        Flow control: none

Thread Notes

Tags: hardware software data converter AD9081 clock and timing AD9081/AD9082 High Speed A/D Converters >10 MSPS Mixed-Signal Front Ends (MxFE) RF Integrated Transceivers Show More

Parents

0 iulia

6 months ago
Hi,

Have you checked out this thread? RE: AD9082-FMCA-EBZ, QPLL RX buffer underflow error With focus on the comment I linked, but not only.

Best regards,
Iulia
Cancel
Up 0 Down

Reply

Verify Answer

Cancel

Reply

0 iulia

6 months ago
Hi,

Have you checked out this thread? RE: AD9082-FMCA-EBZ, QPLL RX buffer underflow error With focus on the comment I linked, but not only.

Best regards,
Iulia
Cancel
Up 0 Down

Reply

Verify Answer

Cancel

Children

0 nirbhay100
6 months ago in reply to iulia
Hi,
I have checked the thread as mentioned in the link.

Now I changed the QPLL0 used for the Tx link to CPLL as in the app_JESD.c file

#ifdef TX_XCVR_BASEADDR
struct adxcvr_init tx_adxcvr_init = {
.name = "tx_adxcvr",
.base = TX_XCVR_BASEADDR,
/*.sys_clk_sel = ADXCVR_SYS_CLK_QPLL0,*/
.sys_clk_sel = ADXCVR_SYS_CLK_CPLL,
.out_clk_sel = ADXCVR_REFCLK_DIV2,
.lpm_enable = 0,
.lane_rate_khz = tx_lane_clk_khz,
.ref_rate_khz = reference_clk_khz,
};
#endif

#ifdef RX_XCVR_BASEADDR
struct adxcvr_init rx_adxcvr_init = {
.name = "rx_adxcvr",
.base = RX_XCVR_BASEADDR,
/*.sys_clk_sel = ADXCVR_SYS_CLK_CPLL,*/
.sys_clk_sel = ADXCVR_SYS_CLK_CPLL,
.out_clk_sel = ADXCVR_REFCLK_DIV2,
/*.lpm_enable = 1,
.lane_rate_khz = rx_lane_clk_khz,
.ref_rate_khz = reference_clk_khz,*/
.lpm_enable = 1,
.lane_rate_khz = rx_lane_clk_khz,
.ref_rate_khz = reference_clk_khz,
};
#endif

TX status is now in data and DACs are working. However, the Rx link status is still in the CGS stage.

The serial terminal log is below:

Hello
rx_adxcvr: OK (10000000 kHz)
tx_adxcvr: OK (10000000 kHz)
ad9081_jesd_rx_link_status_print: JESD TX (JRX) Link1 0x0 lanes in DATA
tx_adxcvr: OK (10000000 kHz)
ad9081_jesd_rx_link_status_print: JESD TX (JRX) Link1 0xF lanes in DATA
ad9081_jesd_tx_link_status_print: JESD RX (JTX) Link1 in DATA, SYNC deasserted, PLL locked, PHASE established, MODE valid
DAC IRQ status 0xf043000040
AD9081 Rev. 3 Grade 10 (API 1.2.2) probed
tx_jesd status:
Link is enabled
Measured Link Clock: 249.997 MHz
Reported Link Clock: 250.000 MHz
Lane rate: 10000.000 MHz
Lane rate / 40: 250.000 MHz
LMFC rate: 7.812 MHz
SYNC~: deasserted
Link status: DATA
SYSREF captured: Yes
SYSREF alignment error: No
rx_jesd status:
Link is enabled
Measured Link Clock: 249.998 MHz
Reported Link Clock: 250.000 MHz
Lane rate: 10000.000 MHz
Lane rate / 40: 250.000 MHz
LMFC rate: 7.812 MHz
Link status: CGS
SYSREF captured: Yes
SYSREF alignment error: No
tx_dac: Successfully initialized (249998474 Hz)
rx_adc: Successfully initialized (249998474 Hz)
Running TinyIIOD server...
If successful, you may connect an IIO client application by:
1. Disconnecting the serial terminal you use to view this message.
2. Connecting the IIO client application using the serial backend configured as shown:
Baudrate: 115200
Data size: 8 bits
Parity: none
Stop bits: 1
Flow control: none

Kindly suggest what can be done.
Cancel
Up 0 Down

Reply

Verify Answer

Cancel

Electronic Design Services - PartnerZone

Products In This Thread

QPLL TX buffer underflow error, status: 0x61

Thread Notes