• State Verified Answer
  • Replies 4 replies
  • Subscribers 42 subscribers
  • Views 350 views
  • Users 0 members are here
Options
Related 

        

            Post
             Go back to editing
        

    

    


    

    









		











	
	
			
	
			
		
	
	
		

		
Questions on AD9262

		
		

		

			

									
						coolparam
					
							

			
				
									
											
			        
                                                			
				
			
		


				
		

		    
		    
		    		    
			
Hi,

 
I have some questions the ADC AD9262

 
1.  In the data sheet, on page 24, it says "When 3.3 V voltage levels are  desirable, the DRVDD power supply must be set to 3.3 V. " It looks to me  like that when the DRVDD is 3.3V, all the digital output, including the  DA0~DA15 and DB0~DA15, SDIO and SCLK are all 3.3V level. However, in  table 6 on page 8, the voltage range of DA0~DA15 and DB0~DB15 are −0.3 V  to +2.0 V.

 
2. Figure 45 shows dual power supply +/-5V for AD4937. However, the data sheet of AD4937 states that it is single +5V supply. Which one should I follow?

 
thank you very much.

 
John

								


				
				
		

			
						
									
									
						
						
			
			
			
			
		


					

			





	

		
	











	

	

					



			








	
	
	
	



Parents
	
    
	

  • 
	
    



	
			
		
	



    
	
    
		
    
							
					
    
		
    
			
													0
							
			
				
									
							
						
				
			
					
    
	
    

		
		
    
					
    Hi Coolparam,
    
 
    Thanks for your questions. Seems the AD9262 Rev A datasheet has a couple of things that need clarification/correction.
    
 
    FIrst off, table 6 on page 8 is the Absolute Maximum Ratings table. This table, give an indication not of the operating points, but rather what the limits are before we know damage will occure to the part. In this case, I agree that the limitation is strange, and should be clarified. The Data outputs 1-16 listed are for the case with the supply at 1.8V.
    
 
    In the case where the supply is 3.3V, the abs max would rise (probably to +3.5V).
    
 
    On fig 47 of the AD9262 datasheet, I would have to agree - that looks wrong. Dual 5 v supplies will fry the part (both parts in all likelyhood).
    
 
    I'd suggest using 3.3V single supply configuration like is shown on the AD4937-2 datasheet, page 25, fig 67. We will need to update our datasheet for the AD9262. Thanks for pointing that out.
    
 
    Thanks
    
 
    -C
    
			
    

		
		
		
		
	
    
	
    
		
    
			
		
    
	
    
	
    
		
						
				
						
						
				
				
		
		
    
			
		
    
	
    

    

    

    • 

	




Reply

    


  • 
	
    



	
			
		
	



    
	
    
		
    
							
					
    
		
    
			
													0
							
			
				
									
							
						
				
			
					
    
	
    

		
		
    
					
    Hi Coolparam,
    
 
    Thanks for your questions. Seems the AD9262 Rev A datasheet has a couple of things that need clarification/correction.
    
 
    FIrst off, table 6 on page 8 is the Absolute Maximum Ratings table. This table, give an indication not of the operating points, but rather what the limits are before we know damage will occure to the part. In this case, I agree that the limitation is strange, and should be clarified. The Data outputs 1-16 listed are for the case with the supply at 1.8V.
    
 
    In the case where the supply is 3.3V, the abs max would rise (probably to +3.5V).
    
 
    On fig 47 of the AD9262 datasheet, I would have to agree - that looks wrong. Dual 5 v supplies will fry the part (both parts in all likelyhood).
    
 
    I'd suggest using 3.3V single supply configuration like is shown on the AD4937-2 datasheet, page 25, fig 67. We will need to update our datasheet for the AD9262. Thanks for pointing that out.
    
 
    Thanks
    
 
    -C
    
			
    

		
		
		
		
	
    
	
    
		
    
			
		
    
	
    
	
    
		
						
				
						
						
				
				
		
		
    
			
		
    
	
    

    

    

    • 





Children
	
No Data