adrv9009在跳频应用中，中间频点出现“######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range”错误

Question

我们需要从300MHz以200MHz的步长跳频至6GHz，在跳频的过程中出现 
 &ldquo;######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range&rdquo; 
 或者 
 &ldquo;######## Error Code = 467, comment:[TALISE_setFhmMode : Out of range fhmInitFreq requested&rdquo; 
 的错误。 
 
 请问出现这个问题的原因可能是什么？

Fullscreen 
 freqlog.txt 
 Download 
 
 nowfreq = 300 ,change per time is[102]ms 
 nowfreq = 500 ,change per time is[102]ms 
 nowfreq = 700 ,change per time is[102]ms 
 nowfreq = 900 ,change per time is[102]ms 
 nowfreq = 1100 ,change per time is[102]ms 
 nowfreq = 1300 ,change per time is[102]ms 
 nowfreq = 1500 ,change per time is[102]ms 
 nowfreq = 1700 ,change per time is[102]ms 
 nowfreq = 1900 ,change per time is[102]ms 
 nowfreq = 2100 ,change per time is[102]ms ######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range
]
 nowfreq = 2300 ,change per time is[8]ms ######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range
]
 nowfreq = 2500 ,change per time is[8]ms ######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range
]
 nowfreq = 2700 ,change per time is[8]ms ######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range
]
 nowfreq = 2900 ,change per time is[8]ms ######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range
]
 nowfreq = 3100 ,change per time is[8]ms ######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range
]
 nowfreq = 3300 ,change per time is[8]ms ######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range
]
 nowfreq = 3500 ,change per time is[8]ms ######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range
]
 nowfreq = 3700 ,change per time is[8]ms ######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range
]
 nowfreq = 3900 ,change per time is[8]ms ######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range
]
 nowfreq = 4100 ,change per time is[8]ms ######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range
]
 nowfreq = 4300 ,change per time is[8]ms ######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range
]
 nowfreq = 4500 ,change per time is[8]ms 
 nowfreq = 4700 ,change per time is[102]ms 
 nowfreq = 4900 ,change per time is[102]ms 
 nowfreq = 5100 ,change per time is[102]ms 
 nowfreq = 5300 ,change per time is[102]ms 
 nowfreq = 5500 ,change per time is[102]ms 
 nowfreq = 5700 ,change per time is[102]ms 
 nowfreq = 5900 ,change per time is[102]ms

Echen5 · Accepted Answer

您必须使用以下结构来设置跳频模式的频率范围： 
 
 设置范围后，调用如下 API 函数设置跳频频率。为确保在设置每个跳频频率之后，RF PLL 有足够的时间稳定到新的频率上（即PLL正常锁定），建议每次跳转后添加延迟（2~5s）： 
 
 你可以参考随附的 IronPython：

Fullscreen 
 ADRV9009 Freq_Hop.txt 
 Download 
 
 ########################
#ADI Demo Python Script
########################

#Import Reference to the DLL
import clr
import System
import time
clr.AddReferenceToFileAndPath("C:\Program Files (x86)\Analog Devices\ADRV9009 Transceiver Evaluation Software\AdiCmdServerClient.dll")
from AdiCmdServerClient import AdiCommandServerClient
from AdiCmdServerClient import Talise
from AdiCmdServerClient import FpgaTalise
from AdiCmdServerClient import Enums
from System import Array
import AdiCmdServerClient
#Create an Instance of the Class
Link = AdiCommandServerClient.Instance

#Connect to the Zynq Platform
if(Link.hw.Connected == 1):
 Connect = 0
else:
 Connect = 1
 Link.hw.Connect("192.168.1.10", 55555)

print Link.Version()

#####################################################################
#Frequency hopping config, this can be set in radio off state only
####################################################################

Link.Talise.RadioOff()
Fhm_Config = Link.Talise.FhmConfig()
Fhm_Config.FhmGpioPin = AdiCmdServerClient.GpioSel.TAL_GPIO_INVALID #TAL_GPIO_04 #TAL_GPIO_INVALID
Fhm_Config.FhmMinFreq_MHz = 300
Fhm_Config.FhmMaxFreq_MHz = 6000
Link.Talise.SetFhmConfig(Fhm_Config)
Link.Talise.RadioOn()

#####################################################################
#Frequency hopping mode setup, this can be called in radio on state
####################################################################
Fhm_Mode = Link.Talise.FhmMode()
Fhm_Mode.FhmEnable = 1
Fhm_Mode.EnableMcsSync = 1
Fhm_Mode.FhmTriggerMode = Talise.FhmTriggerMode.FhmNonGpioMode #FhmGpioMode, FhmNonGpioMode 
Fhm_Mode.FhmExitMode = Talise.FhmExitMode.FhmFullExit #FhmQuickExit, FhmFullExit 
Fhm_Mode.FhmInitFrequency_Hz = 300000000
Link.Talise.SetFhmMode(Fhm_Mode)

####################################################################
#Read back the service frequency before starting frequency hopping
####################################################################

init_freq = 0
init_freq = Link.Talise.GetRfPllFrequency(Link.Talise.PllName.RfPll , 0)

#####################################################################
#Frequency hopping frequency set and can call any nymber of hopps
####################################################################

'''
#Link.Talise.SetFhmHop(300000000)
time.sleep(5)
print Link.Talise.GetFhmRfPllFrequency(0)
Link.Talise.SetFhmHop(500000000)
time.sleep(5)
print Link.Talise.GetFhmRfPllFrequency(0)
Link.Talise.SetFhmHop(700000000)
time.sleep(5)
print Link.Talise.GetFhmRfPllFrequency(0)
Link.Talise.SetFhmHop(900000000)
time.sleep(5)
print Link.Talise.GetFhmRfPllFrequency(0)
Link.Talise.SetFhmHop(1100000000)
time.sleep(5)
print Link.Talise.GetFhmRfPllFrequency(0)
Link.Talise.SetFhmHop(130000000)
time.sleep(5)
print Link.Talise.GetFhmRfPllFrequency(0)
'''

for i in range(0,100,1):
 Link.Talise.SetFhmHop(300000000)
 Link.Talise.SetFhmHop(6000000000)
 Link.Talise.SetFhmHop(300000000)

###################################################################################################################
#Frequency hopping mode disable, make sure to disable after FHM as the RFPLL loop filter BW is restored to default.
###################################################################################################################

Fhm_Mode.FhmEnable = 0
Link.Talise.SetFhmMode(Fhm_Mode)

########################################
#configure back the service frequency 
########################################

Link.Talise.RadioOff()
Link.Talise.SetRfPllFrequency(Link.Talise.PllName.RfPll , init_freq ) 
Link.Talise.RadioOn()


#Disconnect from the Zynq Platform
if(Connect == 1):
 Link.hw.Disconnect())

产品和应用

教育中心

活动中心

Thread Details

adrv9009在跳频应用中，中间频点出现“######## Error Code = 471, comment:[TALISE_setFhmHop : nextFhmRfPllFrequency is out of scan range”错误