Zynq MP First Stage Boot Loader Release 2025.1 May 14 2025 - 12:33:16 NOTICE: BL31: Non secure code at 0x8000000 NOTICE: BL31: v2.12.0(release):v1.1-15211-gdd3512287-dirty NOTICE: BL31: Built : 07:04:54, Apr 24 2025 U-Boot 2025.01-ga09d2660433d (May 16 2025 - 14:46:32 +0000) CPU: ZynqMP Silicon: v3 Chip: zu3eg Model: Analog Devices, Inc. Jupiter SDR Board: Xilinx ZynqMP DRAM: 2 GiB EL Level: EL2 Secure Boot: not authenticated, not encrypted Core: 50 devices, 25 uclasses, devicetree: board NAND: 0 MiB MMC: mmc@ff170000: 0 Loading Environment from FAT... *** Error - No Valid Environment Area found *** Warning - bad env area, using default environment In: serial Out: serial,vidconsole Err: serial,vidconsole Bootmode: LVL_SHFT_SD_MODE1 Reset reason: EXTERNAL Net: ADIN1300 PHY detected at addr 15 adin_get_reg_value: failed to find adi,rx-internal-delay-ps, using default 0 adin_get_reg_value: failed to find adi,tx-internal-delay-ps, using default 0 ZYNQ GEM: ff0e0000, mdio bus ff0e0000, phyaddr 15, interface rgmii-id Warning: ethernet@ff0e0000 (eth0) using random MAC address - 0e:6f:cc:c5:21:28 eth0: ethernet@ff0e0000 scanning bus for devices... SATA link 0 timeout. SATA link 1 timeout. AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl SATA mode flags: 64bit ncq pm clo only pmp fbss pio slum part ccc apst starting USB... No USB controllers found Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot.scr 3833 bytes read in 12 ms (311.5 KiB/s) ## Executing script at 20000000 Trying to load boot images from mmc0 401612675 bytes read in 26390 ms (14.5 MiB/s) ## Loading kernel from FIT Image at 10000000 ... Using 'conf-system-top.dtb' configuration Trying 'kernel-1' kernel subimage Description: Linux kernel Created: 2026-06-11 9:17:17 UTC Type: Kernel Image Compression: gzip compressed Data Start: 0x10000100 Data Size: 16453957 Bytes = 15.7 MiB Architecture: AArch64 OS: Linux Load Address: 0x00200000 Entry Point: 0x00200000 Hash algo: sha256 Hash value: 95d645ab8025efa3620709edc3f7ab1c291ed96f1f688427d0232bf847370420 Verifying Hash Integrity ... sha256+ OK ## Loading ramdisk from FIT Image at 10000000 ... Using 'conf-system-top.dtb' configuration Trying 'ramdisk-1' ramdisk subimage Description: petalinux-image-minimal Created: 2026-06-11 9:17:17 UTC Type: RAMDisk Image Compression: uncompressed Data Start: 0x10fc0d78 Data Size: 385092717 Bytes = 367.3 MiB Architecture: AArch64 OS: Linux Load Address: unavailable Entry Point: unavailable Hash algo: sha256 Hash value: 76f18bce653ebf2ea0b0a1323639fd784a45cb8afa1bffbbe91637dc3fb8aae0 Verifying Hash Integrity ... sha256+ OK ## Loading fdt from FIT Image at 10000000 ... Using 'conf-system-top.dtb' configuration Trying 'fdt-system-top.dtb' fdt subimage Description: Flattened Device Tree blob Created: 2026-06-11 9:17:17 UTC Type: Flat Device Tree Compression: uncompressed Data Start: 0x10fb1358 Data Size: 63822 Bytes = 62.3 KiB Architecture: AArch64 Hash algo: sha256 Hash value: 1443712e4833afb4536e5a1fffc9b7e18aa72f2944462caadd5f6f694ac8ff11 Verifying Hash Integrity ... sha256+ OK Booting using the fdt blob at 0x10fb1358 Working FDT set to 10fb1358 Uncompressing Kernel Image to 200000 Loading Ramdisk to 60e8f000, end 77dcfc6d ... OK Loading Device Tree to 0000000060e7c000, end 0000000060e8e94d ... OK Working FDT set to 60e7c000 No RNG device Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.12.0adi-v2025.1-27393-gc10fc2e1f7cc (oe-user@oe-host) (aarch64-amd-linux-gcc (GCC) 13.3.0, GNU ld (GNU Binutils) 2.42.0.20240723) #1 SMP Thu Jun 11 09:17:17 UTC 2026 [ 0.000000] Machine model: Analog Devices, Inc. Jupiter SDR [ 0.000000] earlycon: cdns0 at MMIO 0x00000000ff010000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [cdns0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] OF: reserved mem: 0x000000003ed00000..0x000000003ed3ffff (256 KiB) nomap non-reusable memory@3ed00000 [ 0.000000] OF: reserved mem: 0x000000003ef00000..0x000000003ef3ffff (256 KiB) nomap non-reusable memory@3ef00000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000003ecfffff] [ 0.000000] node 0: [mem 0x000000003ed00000-0x000000003ed3ffff] [ 0.000000] node 0: [mem 0x000000003ed40000-0x000000003eefffff] [ 0.000000] node 0: [mem 0x000000003ef00000-0x000000003ef3ffff] [ 0.000000] node 0: [mem 0x000000003ef40000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] cma: Reserved 256 MiB at 0x0000000050e00000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.5 [ 0.000000] percpu: Embedded 31 pages/cpu s89944 r8192 d28840 u126976 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: earlycon console=ttyPS0,115200 root=/dev/ram0 rw [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 524288 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 2MB [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x000000007d500000-0x000000007d700000] (2MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000 [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 33.33MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x7b0074340, max_idle_ns: 440795202884 ns [ 0.000000] sched_clock: 56 bits at 33MHz, resolution 30ns, wraps every 2199023255543ns [ 0.008291] Console: colour dummy device 80x25 [ 0.012473] Calibrating delay loop (skipped), value calculated using timer frequency.. 66.66 BogoMIPS (lpj=133332) [ 0.022798] pid_max: default: 32768 minimum: 301 [ 0.027542] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.034811] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.074745] rcu: Hierarchical SRCU implementation. [ 0.074792] rcu: Max phase no-delay instances is 1000. [ 0.079306] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.087328] EFI services will not be available. [ 0.091930] smp: Bringing up secondary CPUs ... [ 0.096704] Detected VIPT I-cache on CPU1 [ 0.096773] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.097272] Detected VIPT I-cache on CPU2 [ 0.097320] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.097793] Detected VIPT I-cache on CPU3 [ 0.097840] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.097904] smp: Brought up 1 node, 4 CPUs [ 0.131921] SMP: Total of 4 processors activated. [ 0.136620] CPU: All CPU(s) started at EL2 [ 0.140710] CPU features: detected: 32-bit EL0 Support [ 0.145843] CPU features: detected: CRC32 instructions [ 0.151011] alternatives: applying system-wide alternatives [ 0.157681] Memory: 1357604K/2097152K available (23232K kernel code, 3470K rwdata, 19488K rodata, 5376K init, 790K bss, 472952K reserved, 262144K cma-reserved) [ 0.171584] devtmpfs: initialized [ 0.180779] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.184913] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.197823] 19616 pages in range for non-PLT usage [ 0.197842] 511136 pages in range for PLT usage [ 0.197995] pinctrl core: initialized pinctrl subsystem [ 0.209562] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.213701] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations [ 0.220340] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.228283] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.235774] audit: initializing netlink subsys (disabled) [ 0.240904] audit: type=2000 audit(0.160:1): state=initialized audit_enabled=0 res=1 [ 0.248531] cpuidle: using governor menu [ 0.252500] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.259282] ASID allocator initialised with 65536 entries [ 0.273669] platform fd4a0000.display: Fixed dependency cycle(s) with /dpcon [ 0.275122] platform dpcon: Fixed dependency cycle(s) with /axi/display@fd4a0000 [ 0.285680] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.289258] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page [ 0.295533] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages [ 0.302313] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page [ 0.308578] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.315363] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.321628] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages [ 0.328412] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page [ 0.402624] raid6: neonx8 gen() 2252 MB/s [ 0.470694] raid6: neonx4 gen() 2207 MB/s [ 0.538774] raid6: neonx2 gen() 2124 MB/s [ 0.606844] raid6: neonx1 gen() 1812 MB/s [ 0.674912] raid6: int64x8 gen() 1415 MB/s [ 0.742989] raid6: int64x4 gen() 1566 MB/s [ 0.811062] raid6: int64x2 gen() 1400 MB/s [ 0.879145] raid6: int64x1 gen() 1033 MB/s [ 0.879191] raid6: using algorithm neonx8 gen() 2252 MB/s [ 0.951211] raid6: .... xor() 1660 MB/s, rmw enabled [ 0.951262] raid6: using neon recovery algorithm [ 0.955592] iommu: Default domain type: Translated [ 0.959928] iommu: DMA domain TLB invalidation policy: strict mode [ 0.972500] SCSI subsystem initialized [ 0.972704] usbcore: registered new interface driver usbfs [ 0.976111] usbcore: registered new interface driver hub [ 0.981416] usbcore: registered new device driver usb [ 0.986625] mc: Linux media interface: v0.10 [ 0.990730] videodev: Linux video capture interface: v2.00 [ 0.996229] pps_core: LinuxPPS API ver. 1 registered [ 1.001139] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.010282] PTP clock support registered [ 1.014216] EDAC MC: Ver: 3.0.0 [ 1.017673] zynqmp-ipi-mbox mailbox@ff9905c0: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.026380] jesd204: found 0 devices and 0 topologies [ 1.030965] FPGA manager framework [ 1.034321] Advanced Linux Sound Architecture Driver Initialized. [ 1.041001] Bluetooth: Core ver 2.22 [ 1.043958] NET: Registered PF_BLUETOOTH protocol family [ 1.049254] Bluetooth: HCI device and connection manager initialized [ 1.055605] Bluetooth: HCI socket layer initialized [ 1.060475] Bluetooth: L2CAP socket layer initialized [ 1.065527] Bluetooth: SCO socket layer initialized [ 1.070859] vgaarb: loaded [ 1.078207] clocksource: Switched to clocksource arch_sys_counter [ 1.079504] VFS: Disk quotas dquot_6.6.0 [ 1.083112] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.096464] NET: Registered PF_INET protocol family [ 1.096655] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 1.104649] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 1.111640] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.119373] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.127386] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear) [ 1.135010] TCP: Hash tables configured (established 16384 bind 16384) [ 1.141186] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 1.147853] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 1.155059] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.161014] RPC: Registered named UNIX socket transport module. [ 1.166525] RPC: Registered udp transport module. [ 1.171218] RPC: Registered tcp transport module. [ 1.175915] RPC: Registered tcp-with-tls transport module. [ 1.181396] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.188816] PCI: CLS 0 bytes, default 64 [ 1.192653] Initialise system trusted keyrings [ 1.196322] workingset: timestamp_bits=46 max_order=19 bucket_order=0 [ 1.202723] Trying to unpack rootfs image as initramfs... [ 1.203195] NFS: Registering the id_resolver key type [ 1.213101] Key type id_resolver registered [ 1.217242] Key type id_legacy registered [ 1.221310] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.227952] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.235378] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 1.242630] fuse: init (API version 7.41) [ 1.302553] NET: Registered PF_ALG protocol family [ 1.302633] xor: measuring software checksum speed [ 1.307810] 8regs : 2518 MB/sec [ 1.312157] 32regs : 2520 MB/sec [ 1.316589] arm64_neon : 2368 MB/sec [ 1.319555] xor: using function: 32regs (2520 MB/sec) [ 1.324611] Key type asymmetric registered [ 1.328698] Asymmetric key parser 'x509' registered [ 1.333662] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.340963] io scheduler mq-deadline registered [ 1.345483] io scheduler kyber registered [ 1.349535] io scheduler bfq registered [ 1.360135] ledtrig-cpu: registered to indicate activity on CPUs [ 1.399621] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.408610] brd: module loaded [ 1.412484] loop: module loaded [ 1.412949] Registered mathworks_ip class [ 1.414544] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.424027] CAN device driver interface [ 1.424665] SPI driver wl1271_spi has no spi_device_id for ti,wl1271 [ 1.430618] SPI driver wl1271_spi has no spi_device_id for ti,wl1273 [ 1.436962] SPI driver wl1271_spi has no spi_device_id for ti,wl1281 [ 1.443312] SPI driver wl1271_spi has no spi_device_id for ti,wl1283 [ 1.449663] SPI driver wl1271_spi has no spi_device_id for ti,wl1285 [ 1.456015] SPI driver wl1271_spi has no spi_device_id for ti,wl1801 [ 1.462369] SPI driver wl1271_spi has no spi_device_id for ti,wl1805 [ 1.468717] SPI driver wl1271_spi has no spi_device_id for ti,wl1807 [ 1.475067] SPI driver wl1271_spi has no spi_device_id for ti,wl1831 [ 1.481419] SPI driver wl1271_spi has no spi_device_id for ti,wl1835 [ 1.487770] SPI driver wl1271_spi has no spi_device_id for ti,wl1837 [ 1.494331] usbcore: registered new interface driver asix [ 1.499536] usbcore: registered new interface driver ax88179_178a [ 1.505634] usbcore: registered new interface driver cdc_ether [ 1.511456] usbcore: registered new interface driver net1080 [ 1.517122] usbcore: registered new interface driver cdc_subset [ 1.523034] usbcore: registered new interface driver zaurus [ 1.528597] usbcore: registered new interface driver cdc_ncm [ 1.534250] usbcore: registered new interface driver r8153_ecm [ 1.541212] usbcore: registered new interface driver uas [ 1.545400] usbcore: registered new interface driver usb-storage [ 1.551441] usbcore: registered new interface driver usbserial_generic [ 1.557915] usbserial: USB Serial support registered for generic [ 1.563920] usbcore: registered new interface driver ftdi_sio [ 1.569663] usbserial: USB Serial support registered for FTDI USB Serial Device [ 1.576971] usbcore: registered new interface driver upd78f0730 [ 1.582883] usbserial: USB Serial support registered for upd78f0730 [ 1.590316] i2c_dev: i2c /dev entries driver [ 1.593984] usbcore: registered new interface driver uvcvideo [ 1.600465] Bluetooth: HCI UART driver ver 2.3 [ 1.603577] Bluetooth: HCI UART protocol H4 registered [ 1.608701] Bluetooth: HCI UART protocol BCSP registered [ 1.614050] Bluetooth: HCI UART protocol LL registered [ 1.619144] Bluetooth: HCI UART protocol ATH3K registered [ 1.624567] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 1.630928] Bluetooth: HCI UART protocol Intel registered [ 1.636222] Bluetooth: HCI UART protocol QCA registered [ 1.641452] usbcore: registered new interface driver bcm203x [ 1.647099] usbcore: registered new interface driver bpa10x [ 1.652668] usbcore: registered new interface driver bfusb [ 1.658142] usbcore: registered new interface driver btusb [ 1.663639] usbcore: registered new interface driver ath3k [ 1.669302] EDAC MC: ECC not enabled [ 1.673090] sdhci: Secure Digital Host Controller Interface driver [ 1.678847] sdhci: Copyright(c) Pierre Ossman [ 1.683177] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.689172] SMCCC: SOC_ID: ID = jep106:0049:0000 Revision = 0x14710093 [ 1.695500] zynqmp_firmware_probe Platform Management API v1.1 [ 1.701217] zynqmp_firmware_probe Trustzone version v1.0 [ 1.738188] zynqmp-aes zynqmp-aes.0: will run requests pump with realtime priority [ 1.740397] zynqmp_rsa zynqmp_rsa.0: This driver is deprecated. Please migrate to xilinx-rsa driver [ 1.749382] usbcore: registered new interface driver usbhid [ 1.754789] usbhid: USB HID core driver [ 1.758808] SPI driver fb_seps525 has no spi_device_id for syncoam,seps525 [ 1.776035] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 (0,8000003f) counters available [ 1.780183] axi_sysid 85000000.axi-sysid-0: AXI System ID core version (1.01.a) found [ 1.787800] axi_sysid 85000000.axi-sysid-0: [jupiter] [USE_RX_CLK_FOR_TX1=0, USE_RX_CLK_FOR_TX2=0] on [sdr] git branch <> git <0> dirty [2026-05-26 13:38:31] UTC [ 1.803146] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered [ 1.808958] usbcore: registered new interface driver snd-usb-audio [ 1.816230] pktgen: Packet Generator for packet performance testing. Version: 2.75 [ 1.827018] Initializing XFRM netlink socket [ 1.827148] NET: Registered PF_INET6 protocol family [ 1.832394] Segment Routing with IPv6 [ 1.835156] In-situ OAM (IOAM) with IPv6 [ 1.839188] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.845494] NET: Registered PF_PACKET protocol family [ 1.849958] NET: Registered PF_KEY protocol family [ 1.854977] can: controller area network core [ 1.859121] NET: Registered PF_CAN protocol family [ 1.863870] can: raw protocol [ 1.866822] can: broadcast manager protocol [ 1.871008] can: netlink gateway - max_hops=1 [ 1.875558] Bluetooth: RFCOMM TTY layer initialized [ 1.880225] Bluetooth: RFCOMM socket layer initialized [ 1.885370] Bluetooth: RFCOMM ver 1.11 [ 1.889117] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 1.894437] Bluetooth: BNEP filters: protocol multicast [ 1.899627] Bluetooth: BNEP socket layer initialized [ 1.904593] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.910504] Bluetooth: HIDP socket layer initialized [ 1.915530] 8021q: 802.1Q VLAN Support v1.8 [ 1.919944] 9pnet: Installing 9P2000 support [ 1.923957] NET: Registered PF_IEEE802154 protocol family [ 1.929340] Key type dns_resolver registered [ 1.933772] NET: Registered PF_VSOCK protocol family [ 1.948836] registered taskstats version 1 [ 1.949017] Loading compiled-in X.509 certificates [ 1.960447] Btrfs loaded, zoned=no, fsverity=no [ 1.960816] alg: No test for xilinx-zynqmp-rsa (zynqmp-rsa) [ 1.986868] domain0: domain0 request failed for node 33: -13 [ 1.986989] xuartps ff000000.serial: error -EACCES: failed to add to PM domain domain0 [ 1.994949] xuartps ff000000.serial: probe with driver xuartps failed with error -13 [ 2.004137] ff010000.serial: ttyPS0 at MMIO 0xff010000 (irq = 25, base_baud = 6249999) is a xuartps [ 2.017368] printk: legacy console [ttyPS0] enabled [ 2.017368] printk: legacy console [ttyPS0] enabled [ 2.022330] printk: legacy bootconsole [cdns0] disabled [ 2.022330] printk: legacy bootconsole [cdns0] disabled [ 2.036450] xilinx-zynqmp-dpdma fd4c0000.dma-controller: Xilinx DPDMA engine is probed [ 2.047474] [drm] Initialized zynqmp-dpsub 1.0.0 for fd4a0000.display on minor 0 [ 3.110267] zynqmp-dpsub fd4a0000.display: [drm] Cannot find any crtc or sizes [ 3.117593] zynqmp-dpsub fd4a0000.display: ZynqMP DisplayPort Subsystem driver probed [ 3.125923] ahci-ceva fd0c0000.ahci: supply ahci not found, using dummy regulator [ 3.133561] ahci-ceva fd0c0000.ahci: supply phy not found, using dummy regulator [ 3.141098] ahci-ceva fd0c0000.ahci: supply target not found, using dummy regulator [ 3.149109] ahci-ceva fd0c0000.ahci: AHCI vers 0001.0301, 32 command slots, 6 Gbps, platform mode [ 3.158000] ahci-ceva fd0c0000.ahci: 2/2 ports implemented (port mask 0x3) [ 3.164878] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 3.178029] scsi host0: ahci-ceva [ 3.181819] scsi host1: ahci-ceva [ 3.185293] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 33 lpm-pol 0 [ 3.194087] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 33 lpm-pol 0 [ 3.205773] spi-nor spi1.0: SPI-NOR-UniqueID 104000c4820f00041d001b00471c0c32cd [ 3.213623] 4 fixed-partitions partitions found on MTD device spi1.0 [ 3.219998] Creating 4 MTD partitions on "spi1.0": [ 3.224797] 0x000000000000-0x000000100000 : "qspi-fsbl-uboot" [ 3.231687] 0x000000100000-0x000000600000 : "qspi-linux" [ 3.238078] 0x000000600000-0x000000620000 : "qspi-device-tree" [ 3.244908] 0x000000620000-0x000000c00000 : "qspi-rootfs" [ 3.252119] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM [ 3.259062] xilinx-axipmon fd0b0000.perf-monitor: Probed Xilinx APM [ 3.265879] xilinx-axipmon fd490000.perf-monitor: Probed Xilinx APM [ 3.272703] xilinx-axipmon ffa10000.perf-monitor: Probed Xilinx APM [ 3.298522] platform fe200000.usb: Fixed dependency cycle(s) with /axi/i2c@ff030000/usb-pd@38/connector [ 3.516606] ata2: SATA link down (SStatus 0 SControl 330) [ 3.522101] ata1: SATA link down (SStatus 0 SControl 330) [ 4.214275] zynqmp-dpsub fd4a0000.display: [drm] Cannot find any crtc or sizes [ 18.201155] Freeing initrd memory: 376064K [ 18.222821] at24 0-0050: supply vcc not found, using dummy regulator [ 18.230147] at24 0-0050: 2048 byte 24c16 EEPROM, writable, 16 bytes/write [ 18.278952] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 39 [ 18.285653] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer with timeout 60s [ 18.346266] mmc0: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit [ 18.415083] mmc0: new ultra high speed DDR50 SDHC card at address aaaa [ 18.422600] mmcblk0: mmc0:aaaa SS32G 29.7 GiB [ 18.432177] mmcblk0: p1 p2 [ 19.558232] random: crng init done [ 22.197529] adrv9002 spi0.0: adrv9002-phy Rev 12.0, Firmware 0.22.64, Stream 0.7.18.0, API version: 68.20.12 successfully initialized [ 22.211334] cf_axi_adc 84a00000.axi-adrv9002-rx-lpc: ADI AIM (10.03.) probed ADC ADRV9002 as MASTER [ 22.234593] cf_axi_dds 84a0a000.axi-adrv9002-tx-lpc: Analog Devices CF_AXI_DDS_DDS MASTER (9.02.b) at 0x84A0A000 mapped to 0x000000008c9b8e19, probed DDS ADRV9002 [ 22.262564] cf_axi_dds 84a0c000.axi-adrv9002-tx2-lpc: Analog Devices CF_AXI_DDS_DDS MASTER (9.02.b) at 0x84A0C000 mapped to 0x000000004c6ae300, probed DDS ADRV9002 [ 22.285500] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 45 (0e:6f:cc:c5:21:28) [ 22.295884] input: gpio-keys-power as /devices/platform/gpio-keys-power/input/input0 [ 22.304007] of_cfs_init [ 22.306480] of_cfs_init: OK [ 22.309344] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 22.365050] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 22.371485] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 22.378928] clk: Disabling unused clocks [ 22.383874] PM: genpd: Disabling unused power domains [ 22.389253] ALSA device list: [ 22.392222] No soundcards found. [ 22.396031] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 22.398165] Freeing unused kernel memory: 5376K [ 22.404656] cfg80211: failed to load regulatory.db [ 22.409244] Run /init as init process [ 22.434539] systemd[1]: System time before build time, advancing clock. [ 22.442008] systemd[1]: Failed to find module 'autofs4' [ 22.456443] systemd[1]: systemd 255.17^ running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA -SMACK +SECCOMP -GCRYPT -GNUTLS +OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 -LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK +XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) [ 22.488350] systemd[1]: Detected architecture arm64. Welcome to PetaLinux 2025.1+release-S05180137 (scarthgap)! [ 22.506339] systemd[1]: Hostname set to . [ 22.511604] systemd[1]: Initializing machine ID from random generator. [ 22.857503] systemd[1]: Queued start job for default target Multi-User System. [ 22.909324] systemd[1]: Created slice Slice /system/getty. [ OK ] Created slice Slice /system/getty. [ 22.927550] systemd[1]: Created slice Slice /system/modprobe. [ OK ] Created slice Slice /system/modprobe. [ 22.947511] systemd[1]: Created slice Slice /system/serial-getty. [ OK ] Created slice Slice /system/serial-getty. [ 22.967120] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 22.986468] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ 23.006414] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 23.026434] systemd[1]: Reached target Path Units. [ OK ] Reached target Path Units. [ 23.038315] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 23.054310] systemd[1]: Reached target Slice Units. [ OK ] Reached target Slice Units. [ 23.066316] systemd[1]: Reached target Swaps. [ OK ] Reached target Swaps. [ 23.103361] systemd[1]: Listening on RPCbind Server Activation Socket. [ OK ] Listening on RPCbind Server Activation Socket. [ 23.122437] systemd[1]: Reached target RPC Port Mapper. [ OK ] Reached target RPC Port Mapper. [ 23.138860] systemd[1]: Listening on Syslog Socket. [ OK ] Listening on Syslog Socket. [ 23.150512] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 23.171044] systemd[1]: Listening on Journal Audit Socket. [ OK ] Listening on Journal Audit Socket. [ 23.190634] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 23.210719] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 23.222833] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 23.242683] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 23.258572] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 23.274598] systemd[1]: Listening on User Database Manager Socket. [ OK ] Listening on User Database Manager Socket. [ 23.310594] systemd[1]: Mounting Huge Pages File System... Mounting Huge Pages File System... [ 23.319278] systemd[1]: Mounting POSIX Message Queue File System... Mounting POSIX Message Queue File System... [ 23.345192] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 23.361341] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 23.377496] systemd[1]: Mounting Temporary Directory /tmp... Mounting Temporary Directory /tmp... [ 23.394305] systemd[1]: Starting Create List of Static Device Nodes... Starting Create List of Static Device Nodes... [ 23.417690] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 23.433975] systemd[1]: Starting Load Kernel Module dm_mod... Starting Load Kernel Module dm_mod... [ 23.449887] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 23.465949] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 23.481931] systemd[1]: Starting Load Kernel Module loop... Starting Load Kernel Module loop... [ 23.497813] systemd[1]: Starting RPC Bind... Starting RPC Bind... [ 23.510701] systemd[1]: File System Check on Root Device was skipped because of an unmet condition check (ConditionPathIsReadWrite=!/). [ 23.529627] systemd[1]: Starting Journal Service... Starting Journal Service... [ 23.546091] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 23.561724] systemd[1]: Starting Generate network units from Kernel command line... Starting Generate network units from Kernel command line... [ 23.580967] openvswitch: Open vSwitch switching datapath [ 23.593672] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 23.616072] systemd-journald[204]: Collecting audit messages is enabled. [ 23.617695] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 23.640549] systemd[1]: Started RPC Bind. [ OK ] Started RPC Bind. [ 23.652005] systemd[1]: Mounted Huge Pages File System. [ OK ] Mounted Huge Pages File System. [ 23.670909] systemd[1]: Mounted POSIX Message Queue File System. [ OK ] Mounted POSIX Message Queue File System. [ 23.690659] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted Kernel Debug File System. [ OK ] Mounted Kernel Trace File System. [ OK ] Mounted Temporary Directory /tmp. [ OK ] Finished Create List of Static Device Nodes. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module dm_mod. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module loop. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Generate network units from Kernel command line. [ OK ] Finished Remount Root and Kernel File Systems. Mounting NFSD configuration filesystem... Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Apply Kernel Variables... Starting Create Static Device Nodes in /dev gracefully... [ 24.007648] systemd-journald[204]: Received client request to flush runtime journal. [FAILED] Failed to mount NFSD configuration filesystem. See 'systemctl status proc-fs-nfsd.mount' for details. [DEPEND] Dependency failed for NFS Mount Daemon. [DEPEND] Dependency failed for NFS server and services. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create Static Device Nodes in /dev gracefully. Starting Create System Users... Starting User Database Manager... [ OK ] Started User Database Manager. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Preparation for Local File Systems. Mounting /var/volatile... Starting Rule-based Manager for Device Events and Files... [ OK ] Mounted /var/volatile. Starting Load/Save OS Random Seed... [ OK ] Reached target Local File Systems. Starting Rebuild Dynamic Linker Cache... Starting Create System Files and Directories... [ OK ] Finished Load/Save OS Random Seed. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Rebuild Dynamic Linker Cache. [ OK ] Finished Create System Files and Directories. Starting Run pending postinsts... Starting Rebuild Journal Catalog... Starting Network Name Resolution... Starting Network Time Synchronization... Starting Wait for udev To Complete Device Initialization... Starting Record System Boot/Shutdown in UTMP... [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Rebuild Journal Catalog. [ OK ] Finished Record System Boot/Shutdown in UTMP. [ OK ] Started Network Name Resolution. [ OK ] Started Network Time Synchronization. [ OK ] Finished Run pending postinsts. [ OK ] Finished Wait for udev To Complete Device Initialization. [ OK ] Created slice Slice /system/systemd-fsck. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target System Time Set. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. Starting File System Check on /dev/mmcblk0p1... Starting File System Check on /dev/mmcblk0p2... Starting Update is Completed... Starting Virtual Console Setup... [ OK ] Finished Update is Completed. [ OK ] Finished Virtual Console Setup. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timer Units. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Listening on D-Bus System Message Bus Socket. Starting sshd.socket... [ OK ] Listening on sshd.socket. [ OK ] Reached target Socket Units. [ OK ] Reached target Basic System. Starting Autostart Application... Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Kernel Logging Service. [ OK ] Started System Logging Service. Starting D-Bus System Message Bus... [ 28.388930] autostart[781]: Hi, we are C2R Design Technologies. [ 28.389373] autostart[781]: Thank you for using your product. [ OK ] Started FANCONTROL Daemon. Starting IPv6 Packet Filtering Framework... Starting IPv4 Packet Filtering Framework... Starting Resets System Activity Logs... Starting User Login Management... Starting OpenSSH Key Generation... [ OK ] Finished Autostart Application. [ OK ] Started D-Bus System Message Bus. [ OK ] Finished IPv6 Packet Filtering Framework. [ OK ] Finished IPv4 Packet Filtering Framework. [ OK ] Finished Resets System Activity Logs. [ OK ] Reached target Preparation for Network. Starting Network Configuration... [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Finished File System Check on /dev/mmcblk0p2. Mounting /run/media/mmcblk0p2... [ OK ] Started FANCONTROL Daemon. [ OK ] Started User Login Management. [ OK ] Mounted /run/media/mmcblk0p2. [ OK ] Started Network Configuration. [ OK ] Reached target Network. [ OK ] Started IIO Daemon. Starting Permit User Sessions... Starting Target Communication Framework agent... [ OK ] Started Xinetd A Powerful Replacement For Inetd. [ OK ] Started Target Communication Framework agent. [ OK ] Finished File System Check on /dev/mmcblk0p1. [ OK ] Finished Permit User Sessions. Mounting /run/media/mmcblk0p1... [ OK ] Started FANCONTROL Daemon. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyPS0. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. Starting Record Runlevel Change in UTMP... [ OK ] Mounted /run/media/mmcblk0p1. [ OK ] Finished Record Runlevel Change in UTMP. [ OK ] Started FANCONTROL Daemon. [ OK ] Finished OpenSSH Key Generation. ******************************************************************************************** The PetaLinux source code and images provided/generated are for demonstration purposes only. Please refer to https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/2741928025/Moving+from+PetaLinux+to+Production+Deployment for more details. ******************************************************************************************** PetaLinux 2025.1+release-S05180137 JUPITERTEST ttyPS0 JUPITERTEST login: root Password: root@JUPITERTEST:~# cd ../ root@JUPITERTEST:/# cd ../ root@JUPITERTEST:/# ls bin dev home lib mnt root sbin sys usr boot etc init media proc run srv tmp var root@JUPITERTEST:/# ip addr add 192.168.1.10/24 dev end0 root@JUPITERTEST:/# ip link set end0 up root@JUPITERTEST:/# ifconfig end0 Link encap:Ethernet HWaddr 0E:6F:CC:C5:21:28 inet addr:192.168.1.10 Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::c6f:ccff:fec5:2128/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:43 errors:0 dropped:0 overruns:0 frame:0 TX packets:30 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3082 (3.0 KiB) TX bytes:5688 (5.5 KiB) Interrupt:45 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:10 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1600 (1.5 KiB) TX bytes:1600 (1.5 KiB) root@JUPITERTEST:/# iio_info iio_info version: 0.26 (git tag:a168e98a) Libiio version: 0.26 (git tag: a168e98) backends: local xml ip usb serial IIO context created with local backend. Backend version: 0.26 (git tag: a168e98) Backend description string: Linux JUPITERTEST 6.12.0adi-v2025.1-27393-gc10fc2e1f7cc #1 SMP Thu Jun 11 09:17:17 UTC 2026 aarch64 IIO context has 2 attributes: local,kernel: 6.12.0adi-v2025.1-27393-gc10fc2e1f7cc uri: local: IIO context has 14 devices: hwmon0: ltc2945 4 channels found: in2: (input) 8 channel-specific attributes found: attr 0: highest value: 866 attr 1: input value: 857 attr 2: lowest value: 855 attr 3: max value: 2047 attr 4: max_alarm value: 0 attr 5: min value: 0 attr 6: min_alarm value: 0 attr 7: reset_history ERROR: Permission denied (13) in1: (input) 8 channel-specific attributes found: attr 0: highest value: 8950 attr 1: input value: 8875 attr 2: lowest value: 8850 attr 3: max value: 102375 attr 4: max_alarm value: 0 attr 5: min value: 0 attr 6: min_alarm value: 0 attr 7: reset_history ERROR: Permission denied (13) curr1: (input) 8 channel-specific attributes found: attr 0: highest value: 1089 attr 1: input value: 975 attr 2: lowest value: 424 attr 3: max value: 5119 attr 4: max_alarm value: 0 attr 5: min value: 0 attr 6: min_alarm value: 0 attr 7: reset_history ERROR: Permission denied (13) power1: (input) 8 channel-specific attributes found: attr 0: input value: 8653125 attr 1: input_highest value: 9662656 attr 2: input_lowest value: 3792563 attr 3: max value: 524287969 attr 4: max_alarm value: 0 attr 5: min value: 0 attr 6: min_alarm value: 0 attr 7: reset_history ERROR: Permission denied (13) No trigger on this device hwmon1: tps6598x_source_psy_0_0038 0 channels found: No trigger on this device hwmon2: tps6598x_source_psy_0_003f 0 channels found: No trigger on this device iio:device0: xilinx-ams 30 channels found: voltage9: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSINTLP attr 1: raw value: 18331 attr 2: scale value: 0.045776367 voltage17: (input) 3 channel-specific attributes found: attr 0: label value: PS_MGTRAVCC attr 1: raw value: 18456 attr 2: scale value: 0.045776367 temp20: (input) 5 channel-specific attributes found: attr 0: input value: -280226 attr 1: label value: Temp_PL attr 2: offset value: -36058 attr 3: raw value: 0 attr 4: scale value: 7.771514892 voltage11: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSAUX attr 1: raw value: 39110 attr 2: scale value: 0.045776367 voltage23: (input) 3 channel-specific attributes found: attr 0: label value: VREFP attr 1: raw value: 0 attr 2: scale value: 0.045776367 voltage15: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSIO1 attr 1: raw value: 19446 attr 2: scale value: 0.091552734 voltage27: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSINTFP attr 1: raw value: 0 attr 2: scale value: 0.045776367 voltage2: (input) 3 channel-specific attributes found: attr 0: label value: VCCINT attr 1: raw value: 18324 attr 2: scale value: 0.045776367 voltage10: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSINTFP attr 1: raw value: 18277 attr 2: scale value: 0.045776367 temp8: (input) 5 channel-specific attributes found: attr 0: input value: 31474 attr 1: label value: Temp_FPD attr 2: offset value: -36058 attr 3: raw value: 40160 attr 4: scale value: 7.771514892 voltage19: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSADC attr 1: raw value: 38906 attr 2: scale value: 0.045776367 voltage6: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSINTFP_DDR attr 1: raw value: 18237 attr 2: scale value: 0.045776367 voltage22: (input) 3 channel-specific attributes found: attr 0: label value: VCCAUX attr 1: raw value: 0 attr 2: scale value: 0.045776367 temp7: (input) 5 channel-specific attributes found: attr 0: input value: 32065 attr 1: label value: Temp_LPD attr 2: offset value: -36058 attr 3: raw value: 40296 attr 4: scale value: 7.771514892 voltage1: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSBATT attr 1: raw value: 39058 attr 2: scale value: 0.045776367 voltage26: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSINTLP attr 1: raw value: 0 attr 2: scale value: 0.045776367 voltage5: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSDDR_PLL attr 1: raw value: 39178 attr 2: scale value: 0.045776367 voltage14: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSIO0 attr 1: raw value: 19435 attr 2: scale value: 0.091552734 voltage24: (input) 3 channel-specific attributes found: attr 0: label value: VREFN attr 1: raw value: 0 attr 2: scale value: 0.045776367 voltage3: (input) 3 channel-specific attributes found: attr 0: label value: VCCBRAM attr 1: raw value: 18350 attr 2: scale value: 0.045776367 voltage12: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSDDR attr 1: raw value: 26193 attr 2: scale value: 0.045776367 voltage18: (input) 3 channel-specific attributes found: attr 0: label value: PS_MGTRAVTT attr 1: raw value: 39240 attr 2: scale value: 0.045776367 voltage16: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSIO2 attr 1: raw value: 19419 attr 2: scale value: 0.091552734 voltage28: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSAUX attr 1: raw value: 0 attr 2: scale value: 0.045776367 voltage21: (input) 3 channel-specific attributes found: attr 0: label value: VCCINT attr 1: raw value: 0 attr 2: scale value: 0.045776367 voltage0: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSPLL attr 1: raw value: 26252 attr 2: scale value: 0.045776367 voltage25: (input) 3 channel-specific attributes found: attr 0: label value: VCCBRAM attr 1: raw value: 0 attr 2: scale value: 0.045776367 voltage4: (input) 3 channel-specific attributes found: attr 0: label value: VCCAUX attr 1: raw value: 39190 attr 2: scale value: 0.045776367 voltage13: (input) 3 channel-specific attributes found: attr 0: label value: VCC_PSIO3 attr 1: raw value: 19409 attr 2: scale value: 0.091552734 voltage29: (input) 3 channel-specific attributes found: attr 0: label value: VCCAMS attr 1: raw value: 0 attr 2: scale value: 0.045776367 1 device-specific attributes found: attr 0: waiting_for_supplier value: 0 No trigger on this device iio:device1: xilinx-system-monitor (buffer capable) 9 channels found: voltage3: vccpsintlp (input, index: 5, format: le:u10/16>>6) 3 channel-specific attributes found: attr 0: label value: vccpsintlp attr 1: raw value: 286 attr 2: scale value: 2.929687500 voltage4: vccpsintfp (input, index: 6, format: le:u10/16>>6) 3 channel-specific attributes found: attr 0: label value: vccpsintfp attr 1: raw value: 286 attr 2: scale value: 2.929687500 voltage5: vccpsaux (input, index: 7, format: le:u10/16>>6) 3 channel-specific attributes found: attr 0: label value: vccpsaux attr 1: raw value: 610 attr 2: scale value: 2.929687500 temp0: (input, index: 8, format: le:u10/16>>6) 3 channel-specific attributes found: attr 0: offset value: -563 attr 1: raw value: 626 attr 2: scale value: 497.376953125 voltage0: vccint (input, index: 9, format: le:u10/16>>6) 3 channel-specific attributes found: attr 0: label value: vccint attr 1: raw value: 288 attr 2: scale value: 2.929687500 voltage1: vccaux (input, index: 10, format: le:u10/16>>6) 3 channel-specific attributes found: attr 0: label value: vccaux attr 1: raw value: 612 attr 2: scale value: 2.929687500 voltage6: vrefp (input, index: 12, format: le:u10/16>>6) 3 channel-specific attributes found: attr 0: label value: vrefp attr 1: raw value: 426 attr 2: scale value: 2.929687500 voltage7: vrefn (input, index: 13, format: le:s10/16>>6) 3 channel-specific attributes found: attr 0: label value: vrefn attr 1: raw value: 0 attr 2: scale value: 2.929687500 voltage2: vccbram (input, index: 14, format: le:u10/16>>6) 3 channel-specific attributes found: attr 0: label value: vccbram attr 1: raw value: 287 attr 2: scale value: 2.929687500 2 device-specific attributes found: attr 0: sampling_frequency value: 147928 attr 1: waiting_for_supplier value: 0 2 buffer-specific attributes found: attr 0: data_available value: 0 attr 1: direction value: in ERROR: checking for trigger : Input/output error (5) iio:device2: adrv9002-phy 17 channels found: voltage0: (output) 27 channel-specific attributes found: attr 0: atten_control_mode value: spi attr 1: atten_control_mode_available value: bypass spi pin closed_loop_gain attr 2: close_loop_gain_tracking_en value: 0 attr 3: dpd_frequency_hopping_regions value: 30000000,6000000000 attr 4: dpd_region0_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 5: dpd_region1_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 6: dpd_region2_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 7: dpd_region3_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 8: dpd_region4_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 9: dpd_region5_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 10: dpd_region6_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 11: dpd_region7_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 12: en value: 1 attr 13: ensm_mode value: rf_enabled attr 14: ensm_mode_available value: calibrated primed rf_enabled attr 15: hardwaregain value: -10.000000 dB attr 16: lo_leakage_tracking_en value: 0 attr 17: loopback_delay_tracking_en value: 0 attr 18: nco_frequency value: 0 attr 19: pa_correction_tracking_en value: 0 attr 20: port_en_mode value: spi attr 21: port_en_mode_available value: spi pin attr 22: port_select value: tx_a attr 23: port_select_available value: tx_a tx_b attr 24: quadrature_tracking_en value: 0 attr 25: rf_bandwidth value: 9000000 attr 26: sampling_frequency value: 15360000 voltage0: (input) 32 channel-specific attributes found: attr 0: agc_tracking_en value: 1 attr 1: bbdc_loop_gain_raw value: 1048576 attr 2: bbdc_rejection_en value: 1 attr 3: bbdc_rejection_tracking_en value: 1 attr 4: decimated_power value: 47.750 dB attr 5: digital_gain_control_mode value: spi attr 6: digital_gain_control_mode_available value: automatic spi attr 7: dynamic_adc_switch_en value: 0 attr 8: en value: 1 attr 9: ensm_mode value: rf_enabled attr 10: ensm_mode_available value: calibrated primed rf_enabled attr 11: gain_control_mode value: spi attr 12: gain_control_mode_available value: spi pin automatic attr 13: hardwaregain value: 34.000000 dB attr 14: hd_tracking_en value: 0 attr 15: interface_gain value: 0dB attr 16: interface_gain_available value: 0dB attr 17: nco_frequency value: 0 attr 18: orx_bbdc_rejection_en ERROR: No such device (19) attr 19: orx_en ERROR: No such device (19) attr 20: orx_hardwaregain ERROR: No such device (19) attr 21: orx_label value: orx attr 22: orx_quadrature_w_poly_tracking_en ERROR: No such device (19) attr 23: port_en_mode value: spi attr 24: port_en_mode_available value: spi pin attr 25: quadrature_fic_tracking_en value: 1 attr 26: quadrature_w_poly_tracking_en value: 0 attr 27: rf_bandwidth value: 9000000 attr 28: rfdc_tracking_en value: 1 attr 29: rssi value: 81.867 dB attr 30: rssi_tracking_en value: 1 attr 31: sampling_frequency value: 15360000 voltage1: (input) 32 channel-specific attributes found: attr 0: agc_tracking_en value: 1 attr 1: bbdc_loop_gain_raw value: 1048576 attr 2: bbdc_rejection_en value: 1 attr 3: bbdc_rejection_tracking_en value: 1 attr 4: decimated_power value: 46.250 dB attr 5: digital_gain_control_mode value: spi attr 6: digital_gain_control_mode_available value: automatic spi attr 7: dynamic_adc_switch_en value: 0 attr 8: en value: 1 attr 9: ensm_mode value: rf_enabled attr 10: ensm_mode_available value: calibrated primed rf_enabled attr 11: gain_control_mode value: spi attr 12: gain_control_mode_available value: spi pin automatic attr 13: hardwaregain value: 34.000000 dB attr 14: hd_tracking_en value: 0 attr 15: interface_gain value: 0dB attr 16: interface_gain_available value: 0dB attr 17: nco_frequency value: 0 attr 18: orx_bbdc_rejection_en ERROR: No such device (19) attr 19: orx_en ERROR: No such device (19) attr 20: orx_hardwaregain ERROR: No such device (19) attr 21: orx_label value: orx attr 22: orx_quadrature_w_poly_tracking_en ERROR: No such device (19) attr 23: port_en_mode value: spi attr 24: port_en_mode_available value: spi pin attr 25: quadrature_fic_tracking_en value: 1 attr 26: quadrature_w_poly_tracking_en value: 0 attr 27: rf_bandwidth value: 9000000 attr 28: rfdc_tracking_en value: 1 attr 29: rssi value: 81.993 dB attr 30: rssi_tracking_en value: 1 attr 31: sampling_frequency value: 15360000 voltage1: (output) 27 channel-specific attributes found: attr 0: atten_control_mode value: spi attr 1: atten_control_mode_available value: bypass spi pin closed_loop_gain attr 2: close_loop_gain_tracking_en value: 0 attr 3: dpd_frequency_hopping_regions value: 30000000,6000000000 attr 4: dpd_region0_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 5: dpd_region1_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 6: dpd_region2_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 7: dpd_region3_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 8: dpd_region4_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 9: dpd_region5_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 10: dpd_region6_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 11: dpd_region7_coefficients value: 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0 attr 12: en value: 1 attr 13: ensm_mode value: rf_enabled attr 14: ensm_mode_available value: calibrated primed rf_enabled attr 15: hardwaregain value: -10.000000 dB attr 16: lo_leakage_tracking_en value: 0 attr 17: loopback[ 493.272479] adrv9002 spi0.0: Frequency hopping not enabled _delay_tracking_en value: 0 attr 18: nco_frequency value: 0 [ 493.283787] adrv9002 spi0.0: Frequency hopping not enabled attr 19: pa_correction_tracking_en value: 0 attr 20: port_en_mode value: spi attr 21: port_en_mode_available value: spi pin attr 22: port_select value: tx_a attr 23: port_select_available value: tx_a tx_b attr 24: quadrature_tracking_en value: 0 attr 25: rf_bandwidth value: 9000000 attr 26: sampling_frequency value: 15360000 voltage3: (output) 2 channel-specific attributes found: attr 0: en value: 0 attr 1: input value: 50 altvoltage2: TX1_LO (output) 2 channel-specific attributes found: attr 0: frequency value: 2500000000 attr 1: label value: TX1_LO voltage5: (input) 2 channel-specific attributes found: attr 0: en value: 0 attr 1: input value: 0 voltage3: (input) 2 channel-specific attributes found: attr 0: en value: 0 attr 1: input value: 0 voltage5: (output) 2 channel-specific attributes found: attr 0: en value: 0 attr 1: input value: 50 altvoltage1: RX2_LO (output) 2 channel-specific attributes found: attr 0: frequency value: 2400000000 attr 1: label value: RX2_LO voltage2: (input) 2 channel-specific attributes found: attr 0: en value: 0 attr 1: input value: 0 voltage2: (output) 2 channel-specific attributes found: attr 0: en value: 0 attr 1: input value: 50 altvoltage0: RX1_LO (output) 2 channel-specific attributes found: attr 0: frequency value: 2400000000 attr 1: label value: RX1_LO altvoltage3: TX2_LO (output) 2 channel-specific attributes found: attr 0: frequency value: 2500000000 attr 1: label value: TX2_LO voltage4: (output) 2 channel-specific attributes found: attr 0: en value: 0 attr 1: input value: 50 voltage4: (input) 2 channel-specific attributes found: attr 0: en value: 0 attr 1: input value: 0 temp0: (input) 1 channel-specific attributes found: attr 0: input value: 60000 17 device-specific attributes found: attr 0: frequency_hopping_hop1_signal_trigger ERROR: Permission denied (13) attr 1: frequency_hopping_hop1_table_a ERROR: Permission denied (13) attr 2: frequency_hopping_hop1_table_b ERROR: Permission denied (13) attr 3: frequency_hopping_hop1_table_select ERROR: Unknown error 524 attr 4: frequency_hopping_hop2_signal_trigger ERROR: Permission denied (13) attr 5: frequency_hopping_hop2_table_a ERROR: Permission denied (13) attr 6: frequency_hopping_hop2_table_b ERROR: Permission denied (13) attr 7: frequency_hopping_hop2_table_select ERROR: Unknown error 524 attr 8: frequency_hopping_hop_table_select_available value: TABLE_A TABLE_B attr 9: initial_calibrations value: off attr 10: initial_calibrations_available value: off auto run attr 11: multi_chip_sync ERROR: Permission denied (13) attr 12: profile_config value: Device clk(Hz): 38400000 Clk PLL VCO(Hz): 8847360000 ARM Power Saving Clk Divider: 1 RX1 LO: L02 RX2 LO: L02 TX1 LO: L01 TX1 DPD enable: 0 TX2 LO: L01 TX2 DPD enable: 0 RX1 Gain Table Type: Correction RX2 Gain Table Type: Correction RX Channel Mask: 0xc3 TX Channel Mask: 0xc Duplex Mode: FDD FH enable: 0 MCS mode: Disabled WarmBoot: Enabled SSI interface: LVDS attr 13: stream_config ERROR: Permission denied (13) attr 14: waiting_for_supplier value: 0 attr 15: warmboot_coefficients ERROR: File too large (27) attr 16: warmboot_coefficients_file value: Navassa_LVDS_init_cals.bin 376 debug attributes found: debug attr 0: pll_aux_power_scale value: 5 debug attr 1: pll_aux_phase_margin_deg value: 60 debug attr 2: pll_aux_loop_b[ 494.724599] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. andwidth_khz value: 300 debug attr 3: pll_aux_power value:[ 494.761021] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. 0 debug attr 4: pll_aux_calibration_mode value: 0 de[ 494.793741] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) bug attr 5: pll_lo2_power_scale value: 5 debug attr 6: pll_[ 494.811048] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. lo2_phase_margin_deg value: 60 debug attr 7: pll_lo2_loop_[ 494.847459] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. bandwidth_khz value: 300 debug attr 8: pll_lo2_power value[ 494.880184] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) : 0 debug attr 9: pll_lo2_calibration_mode value: 0 deb[ 494.897541] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. ug attr 10: pll_lo1_power_scale value: 5 debug attr 11: pll[ 494.933918] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. _lo1_phase_margin_deg value: 60 debug attr 12: pll_lo1_loop[ 494.966632] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) _bandwidth_khz value: 300 debug attr 13: pll_lo1_power value[ 494.983892] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. : 0 debug attr 14: pll_lo1_calibration_mode value: 0 d[ 495.020282] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. ebug attr 15: agpio11_direction value: 0 debug attr 16: agp[ 495.052992] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) io11_value value: 0 debug attr 17: agpio10_direction value: 0 debug attr 18: agpio10_value value: 0 debug attr 19: agpio9_direction value: 0 debug attr 20: agpio9_value value: 0 debug attr 21: agpio8_direction value: 0 debug attr 22: agpio8_value value: 0 debug attr 23: agpio7_direction value: 0 debug attr 24: agpio7_value value: 0 debug attr 25: agpio6_direction value: 0 debug attr 26: agpio6_value value: 0 debug attr 27: agpio5_direction value: 0 debug attr 28: agpio5_value value: 0 debug attr 29: agpio4_direction value: 0 debug attr 30: agpio4_value value: 0 debug attr 31: agpio3_direction value: 0 debug attr 32: agpio3_value value: 0 debug attr 33: agpio2_direction value: 0 debug attr 34: agpio2_value value: 0 debug attr 35: agpio1_direction value: 0 debug attr 36: agpio1_value value: 0 debug attr 37: agpio0_direction value: 0 debug attr 38: agpio0_value value: 0 debug attr 39: dgpio15_direction value: 0 debug attr 40: dgpio15_value value: 1 debug attr 41: dgpio14_direction value: 0 debug attr 42: dgpio14_value value: 1 debug attr 43: dgpio13_direction value: 0 debug attr 44: dgpio13_value value: 1 debug attr 45: dgpio12_direction value: 0 debug attr 46: dgpio12_value value: 1 debug attr 47: dgpio11_direction value: 0 debug attr 48: dgpio11_value value: 0 debug attr 49: dgpio10_direction value: 0 debug attr 50: dgpio10_value value: 0 debug attr 51: dgpio9_direction value: 0 debug attr 52: dgpio9_value value: 0 debug attr 53: dgpio8_direction value: 0 debug attr 54: dgpio8_value value: 0 debug attr 55: dgpio7_direction value: 0 debug attr 56: dgpio7_value value: 0 debug attr 57: dgpio6_direction value: 0 debug attr 58: dgpio6_value value: 0 debug attr 59: dgpio5_direction value: 0 debug attr 60: dgpio5_value value: 0 debug attr 61: dgpio4_direction value: 0 debug attr 62: dgpio4_value value: 0 debug attr 63: dgpio3_direction value: 0 debug attr 64: dgpio3_value value: 0 debug attr 65: dgpio2_direction value: 0 debug attr 66: dgpio2_value value: 1 debug attr 67: dgpio1_direction value: 0 debug attr 68: dgpio1_value value: 0 debug attr 69: dgpio0_direction value: 0 debug attr 70: dgpio0_value value: 0 debug attr 71: fh_config_dump value: mode: 0 RX1 Hop Signal: 1 RX2 Hop Signal: 1 TX1 Hop Signal: 1 TX2 Hop Signal: 1 rxZeroIfEnable: 0 Hop Signal 1 pin: Unassigned Hop Signal 2 pin: Unassigned hopTableSelectMode: 0 Hop Signal 1 table select pin: Unassigned Hop Signal 2 table select pin: Unassigned minRxGainIndex: 0 maxRxGainIndex: 0 minTxAtten_mdB: 0 maxTxAtten_mdB: 0 minOperatingFrequency_Hz: 0 maxOperatingFrequency_Hz: 0 minFrameDuration_us: 0 txAnalogPowerOnFrameDelay: 0 tableIndexCtrl: 0 numTableIndexPins: 0 gainSetupByPin: 0 debug attr 72: fh_tx1_port_hop_signal value: 1 debug attr 73: fh_rx1_port_hop_signal value: 1 debug attr 74: fh_tx0_port_hop_signal value: 0 debug attr 75: fh_rx0_port_hop_signal value: 0 debug attr 76: fh_hop2_table_b_dump ERROR: Bad address (14) debug attr 77: fh_hop2_table_a_dump ERROR: Bad address (14) debug attr 78: fh_hop2_table_select_pin_set value: 0 debug attr 79: fh_hop2_pin_set value: 0 debug attr 80: fh_hop1_table_b_dump ERROR: Bad address (14) debug attr 81: fh_hop1_table_a_dump ERROR: Bad address (14) debug attr 82: fh_hop1_table_select_pin_set value: 0 debug attr 83: fh_hop1_pin_set value: 0 debug attr 84: fh_hop_table_mode_select value: 0 debug attr 85: fh_table_index_control_pin6 value: 0 debug attr 86: fh_table_index_control_pin5 value: 0 debug attr 87: fh_table_index_control_pin4 value: 0 debug attr 88: fh_table_index_control_pin3 value: 0 debug attr 89: fh_table_index_control_pin2 value: 0 debug attr 90: fh_table_index_control_pin1 value: 0 debug attr 91: fh_table_index_control_npins value: 0 debug attr 92: fh_table_index_control_mode value: 0 debug attr 93: fh_max_lo_freq_hz value: 6000000000 debug attr 94: fh_min_lo_freq_hz value: 25000000 debug attr 95: fh_min_frame_duration_us value: 0 debug attr 96: fh_mode value: 3 debug attr 97: fh_max_tx_atten_mdb value: 41950 debug attr 98: fh_min_tx_atten_mdb value: 0 debug attr 99: fh_rx_zero_if_en value: Y debug attr 100: fh_tx_analog_power_on_frame_delay value: 0 debug attr 101: fh_max_rx_gain value: 255 debug attr 102: fh_min_rx_gain value: 187 debug attr 103: rx1_cals_internal_path_delay_ns value: 7552 debug attr 104: rx1_mcs_delays value: readDelay: 0 sampleDelay: 0 debug attr 105: rx1_mcs_sample_delay value: 0 debug attr 106: rx1_mcs_read_delay value: 1 debug attr 107: rx1_carrier_hz value: 0 debug attr 108: rx1_near_end_loopback ERROR: Permission denied (13) debug attr 109: rx1_enablement_delays value: fall_to_off_delay: 0 guard_delay: 0 hold_delay: 0 rise_to_analog_on_delay: 0 rise_to_on_delay: 0 debug attr 110: rx1_rise_to_on_delay_ns value: 0 debug attr 111: rx1_rise_to_analog_delay_ns value: 0 debug attr 112: rx1_hold_delay_ns value: 0 debug attr 113: rx1_guard_delay_ns value: 0 debug attr 114: rx1_fall_to_off_delay_ns value: 0 debug attr 115: rx1_ssi_q_data_delay value: 0 debug attr 116: rx1_ssi_i_data_delay value: 0 debug attr 117: rx1_ssi_strobe_delay value: 0 debug attr 118: rx1_ssi_clk_delay value: 0 debug attr 119: rx1_agc_peak.feedback_apd_high_hb_high value: 0 debug attr 120: rx1_agc_peak.feedback_apd_low_hb_low value: 0 debug attr 121: rx1_agc_peak.hbUnderRangeLowThreshExceededCount value: 3 debug attr 122: rx1_agc_peak.hbUnderRangeMidThreshExceededCount value: 3 debug attr 123: rx1_agc_peak.hbOverloadPowerMode value: 0 debug attr 124: rx1_agc_peak.hbGainStepAttack value: 2 debug attr 125: rx1_agc_peak.hbGainStepMidRecovery value: 4 debug attr 126: rx1_agc_peak.hbGainStepLowRecovery value: 6 debug attr 127: rx1_agc_peak.hbGainStepHighRecovery value: 2 debug attr 128: rx1_agc_peak.hbUnderRangeHighThreshExceededCount value: 3 debug attr 129: rx1_agc_peak.hbUpperThreshPeakExceededCount value: 6 debug attr 130: rx1_agc_peak.hbUnderRangeHighThresh value: 7335 debug attr 131: rx1_agc_peak.hbUnderRangeMidThresh value: 8230 debug attr 132: rx1_agc_peak.hbUnderRangeLowThresh value: 5826 debug attr 133: rx1_agc_peak.hbHighThresh value: 13044 debug attr 134: rx1_agc_peak.hbOverloadThreshCount value: 1 debug attr 135: rx1_agc_peak.hbOverloadDurationCount value: 1 debug attr 136: rx1_agc_peak.enableHbOverload value: Y debug attr 137: rx1_agc_peak.apdGainStepRecovery value: 0 debug attr 138: rx1_agc_peak.apdGainStepAttack value: 2 debug attr 139: rx1_agc_peak.apdLowerThreshPeakExceededCount value: 3 debug attr 140: rx1_agc_peak.apdUpperThreshPeakExceededCount value: 6 debug attr 141: rx1_agc_peak.apdLowThresh value: 12 debug attr 142: rx1_agc_peak.apdHighThresh value: 21 debug attr 143: rx1_agc_peak.agcUnderRangeHighInterval value: 4 debug attr 144: rx1_agc_peak.agcUnderRangeMidInterval value: 2 debug attr 145: rx1_agc_peak.agcUnderRangeLowInterval value: 50 debug attr 146: rx1_agc_power.feedback_apd_high_apd_low value: 0 debug attr 147: rx1_agc_power.feedback_inner_high_inner_low value: 0 debug attr 148: rx1_agc_power.overRangeLowPowerGainStepAttack value: 4 debug attr 149: rx1_agc_power.overRangeHighPowerGainStepAttack value: 4 debug attr 150: rx1_agc_power.overRangeLowPowerThresh value: 7 debug attr 151: rx1_agc_power.overRangeHighPowerThresh value: 0 debug attr 152: rx1_agc_power.rxTddPowerMeasDelay value: 0 debug attr 153: rx1_agc_power.rxTddPowerMeasDuration value: 0 debug attr 154: rx1_agc_power.powerMeasurementDelay value: 2 debug attr 155: rx1_agc_power.powerMeasurementDuration value: 10 debug attr 156: rx1_agc_power.underRangeLowPowerGainStepRecovery value: 4 debug attr 157: rx1_agc_power.underRangeHighPowerGainStepRecovery value: 2 debug attr 158: rx1_agc_power.underRangeLowPowerThresh value: 4 debug attr 159: rx1_agc_power.underRangeHighPowerThresh value: 10 debug attr 160: rx1_agc_power.powerEnableMeasurement value: Y debug attr 161: rx1_agc_enableFastRecoveryLoop value: N debug attr 162: rx1_agc_enableSyncPulseForGainCounter value: N debug attr 163: rx1_agc_resetOnRxonGainIndex value: 255 debug attr 164: rx1_agc_resetOnRxon value: N debug attr 165: rx1_agc_agcMode value: 1 debug attr 166: rx1_agc_changeGainIfThreshHigh value: 3 debug attr 167: rx1_agc_lowThreshPreventGainInc value: N debug attr 168: rx1_agc_slowLoopSettlingDelay value: 16 debug attr 169: rx1_agc_attackDelay_us value: 10 debug attr 170: rx1_agc_gainUpdateCounter value: 11520 debug attr 171: rx1_agc_minGainIndex value: 187 debug attr 172: rx1_agc_maxGainIndex value: 255 debug attr 173: rx1_agc_peakWaitTime value: 4 debug attr 174: rx1_ssi_test_mode_configure ERROR: Permission denied (13) debug attr 175: rx1_ssi_test_mode_fixed_pattern value: 0 debug attr 176: rx1_ssi_test_mode_data value: TESTMODE_DATA_NORMAL debug attr 177: rx1_agc_config value: peakWaitTime: 4 maxGainIndex: 255 minGainIndex: 187 gainUpdateCounter: 11520 attackDelay_us: 10 slowLoopSettlingDelay: 16 lowThreshPreventGainInc: 0 changeGainIfThreshHigh: 3 agcMode: 1 resetOnRxon: 0 resetOnRxonGainIndex: 255 enableSyncPulseForGainCounter: 0 enableFastRecoveryLoop: 0 power.powerEnableMeasurement: 1 power.underRangeHighPowerThresh: 10 power.underRangeLowPowerThresh: 4 power.underRangeHighPowerGainStepRecovery: 2 power.underRangeLowPowerGainStepRecovery: 4 power.powerMeasurementDuration: 10 power.powerMeasurementDelay: 2 power.rxTddPowerMeasDuration: 0 power.rxTddPowerMeasDelay: 0 power.overRangeHighPowerThresh: 0 power.overRangeLowPowerThresh: 7 power.overRangeHighPowerGainStepAttack: 4 power.overRangeLowPowerGainStepAttack: 4 power.feedback_inner_high_inner_low: 0 power.feedback_apd_high_apd_low: 0 peak.agcUnderRangeLowInterval: 50 peak.agcUnderRangeMidInterval: 2 peak.agcUnderRangeHighInterval: 4 peak.apdHighThresh: 21 peak.apdLowThresh: 12 peak.apdUpperThreshPeakExceededCount: 6 peak.apdLowerThreshPeakExceededCount: 3 peak.apdGainStepAttack: 2 peak.apdGainStepRecovery: 0 peak.enableHbOverload: 1 peak.hbOverloadDurationCount: 1 peak.hbOverloadThreshCount: 1 peak.hbHighThresh: 13044 peak.hbUnderRangeLowThresh: 5826 peak.hbUnderRangeMidThresh: 8230 peak.hbUnderRangeHighThresh: 7335 peak.hbUpperThreshPeakExceededCount: 6 peak.hbUnderRangeHighThreshExceededCount: 3 peak.hbGainStepHighRecovery: 2 peak.hbGainStepLowRecovery: 6 peak.hbGainStepMidRecovery: 4 peak.hbGainStepAttack: 2 peak.hbOverloadPowerMode: 0 peak.hbUnderRangeMidThreshExceededCount: 3 peak.hbUnderRangeLowThreshExceededCount: 3 peak.feedback_apd_low_hb_low: 0 peak.feedback_apd_high_hb_high: 0 debug attr 178: rx1_gain_control_pin_mode value: min_gain_index: 187 max_gain_index: 255 increment_step_size: 1 decrement_step_size: 1 increment_pin: dgpio0 decrement_pin: dgpio0 debug attr 179: rx1_adc_type value: HP debug attr 180: rx0_cals_internal_path_delay_ns value: 7552 debug attr 181: rx0_mcs_delays value: readDelay: 0 sampleDelay: 0 debug attr 182: rx0_mcs_sample_delay value: 0 debug attr 183: rx0_mcs_read_delay value: 1 debug attr 184: rx0_carrier_hz value: 0 debug attr 185: rx0_near_end_loopback ERROR: Permission denied (13) debug attr 186: rx0_enablement_delays value: fall_to_off_delay: 0 guard_delay: 0 hold_delay: 0 rise_to_analog_on_delay: 0 rise_to_on_delay: 0 debug attr 187: rx0_rise_to_on_delay_ns value: 0 debug attr 188: rx0_rise_to_analog_delay_ns value: 0 debug attr 189: rx0_hold_delay_ns value: 0 debug attr 190: rx0_guard_delay_ns value: 0 debug attr 191: rx0_fall_to_off_delay_ns value: 0 debug attr 192: rx0_ssi_q_data_delay value: 0 debug attr 193: rx0_ssi_i_data_delay value: 0 debug attr 194: rx0_ssi_strobe_delay value: 0 debug attr 195: rx0_ssi_clk_delay value: 0 debug attr 196: rx0_agc_peak.feedback_apd_high_hb_high value: 0 debug attr 197: rx0_agc_peak.feedback_apd_low_hb_low value: 0 debug attr 198: rx0_agc_peak.hbUnderRangeLowThreshExceededCount value: 3 debug attr 199: rx0_agc_peak.hbUnderRangeMidThreshExceededCount value: 3 debug attr 200: rx0_agc_peak.hbOverloadPowerMode value: 0 debug attr 201: rx0_agc_peak.hbGainStepAttack value: 2 debug attr 202: rx0_agc_peak.hbGainStepMidRecovery value: 4 debug attr 203: rx0_agc_peak.hbGainStepLowRecovery value: 6 debug attr 204: rx0_agc_peak.hbGainStepHighRecovery value: 2 debug attr 205: rx0_agc_peak.hbUnderRangeHighThreshExceededCount value: 3 debug attr 206: rx0_agc_peak.hbUpperThreshPeakExceededCount value: 6 debug attr 207: rx0_agc_peak.hbUnderRangeHighThresh value: 7335 debug attr 208: rx0_agc_peak.hbUnderRangeMidThresh value: 8230 debug attr 209: rx0_agc_peak.hbUnderRangeLowThresh value: 5826 debug attr 210: rx0_agc_peak.hbHighThresh value: 13044 debug attr 211: rx0_agc_peak.hbOverloadThreshCount value: 1 debug attr 212: rx0_agc_peak.hbOverloadDurationCount value: 1 debug attr 213: rx0_agc_peak.enableHbOverload value: Y debug attr 214: rx0_agc_peak.apdGainStepRecovery value: 0 debug attr 215: rx0_agc_peak.apdGainStepAttack value: 2 debug attr 216: rx0_agc_peak.apdLowerThreshPeakExceededCount value: 3 debug attr 217: rx0_agc_peak.apdUpperThreshPeakExceededCount value: 6 debug attr 218: rx0_agc_peak.apdLowThresh value: 12 debug attr 219: rx0_agc_peak.apdHighThresh value: 21 debug attr 220: rx0_agc_peak.agcUnderRangeHighInterval value: 4 debug attr 221: rx0_agc_peak.agcUnderRangeMidInterval value: 2 debug attr 222: rx0_agc_peak.agcUnderRangeLowInterval value: 50 debug attr 223: rx0_agc_power.feedback_apd_high_apd_low value: 0 debug attr 224: rx0_agc_power.feedback_inner_high_inner_low value: 0 debug attr 225: rx0_agc_power.overRangeLowPowerGainStepAttack value: 4 debug attr 226: rx0_agc_power.overRangeHighPowerGainStepAttack value: 4 debug attr 227: rx0_agc_power.overRangeLowPowerThresh value: 7 debug attr 228: rx0_agc_power.overRangeHighPowerThresh value: 0 debug attr 229: rx0_agc_power.rxTddPowerMeasDelay value: 0 debug attr 230: rx0_agc_power.rxTddPowerMeasDuration value: 0 debug attr 231: rx0_agc_power.powerMeasurementDelay value: 2 debug attr 232: rx0_agc_power.powerMeasurementDuration value: 10 debug attr 233: rx0_agc_power.underRangeLowPowerGainStepRecovery value: 4 debug attr 234: rx0_agc_power.underRangeHighPowerGainStepRecovery value: 2 debug attr 235: rx0_agc_power.underRangeLowPowerThresh value: 4 debug attr 236: rx0_agc_power.underRangeHighPowerThresh value: 10 debug attr 237: rx0_agc_power.powerEnableMeasurement value: Y debug attr 238: rx0_agc_enableFastRecoveryLoop value: N debug attr 239: rx0_agc_enableSyncPulseForGainCounter value: N debug attr 240: rx0_agc_resetOnRxonGainIndex value: 255 debug attr 241: rx0_agc_resetOnRxon value: N debug attr 242: rx0_agc_agcMode value: 1 debug attr 243: rx0_agc_changeGainIfThreshHigh value: 3 debug attr 244: rx0_agc_lowThreshPreventGainInc value: N debug attr 245: rx0_agc_slowLoopSettlingDelay value: 16 debug attr 246: rx0_agc_attackDelay_us value: 10 debug attr 247: rx0_agc_gainUpdateCounter value: 11520 debug attr 248: rx0_agc_minGainIndex value: 187 debug attr 249: rx0_agc_maxGainIndex value: 255 debug attr 250: rx0_agc_peakWaitTime value: 4 debug attr 251: rx0_ssi_test_mode_configure ERROR: Permission denied (13) debug attr 252: rx0_ssi_test_mode_fixed_pattern value: 0 debug attr 253: rx0_ssi_test_mode_data value: TESTMODE_DATA_NORMAL debug attr 254: rx0_agc_config value: peakWaitTime: 4 maxGainIndex: 255 minGainIndex: 187 gainUpdateCounter: 11520 attackDelay_us: 10 slowLoopSettlingDelay: 16 lowThreshPreventGainInc: 0 changeGainIfThreshHigh: 3 agcMode: 1 resetOnRxon: 0 resetOnRxonGainIndex: 255 enableSyncPulseForGainCounter: 0 enableFastRecoveryLoop: 0 power.powerEnableMeasurement: 1 power.underRangeHighPowerThresh: 10 power.underRangeLowPowerThresh: 4 power.underRangeHighPowerGainStepRecovery: 2 power.underRangeLowPowerGainStepRecovery: 4 power.powerMeasurementDuration: 10 power.powerMeasurementDelay: 2 power.rxTddPowerMeasDuration: 0 power.rxTddPowerMeasDelay: 0 power.overRangeHighPowerThresh: 0 power.overRangeLowPowerThresh: 7 power.overRangeHighPowerGainStepAttack: 4 power.overRangeLowPowerGainStepAttack: 4 power.feedback_inner_high_inner_low: 0 power.feedback_apd_high_apd_low: 0 peak.agcUnderRangeLowInterval: 50 peak.agcUnderRangeMidInterval: 2 peak.agcUnderRangeHighInterval: 4 peak.apdHighThresh: 21 peak.apdLowThresh: 12 peak.apdUpperThreshPeakExceededCount: 6 peak.apdLowerThreshPeakExceededCount: 3 peak.apdGainStepAttack: 2 peak.apdGainStepRecovery: 0 peak.enableHbOverload: 1 peak.hbOverloadDurationCount: 1 peak.hbOverloadThreshCount: 1 peak.hbHighThresh: 13044 peak.hbUnderRangeLowThresh: 5826 peak.hbUnderRangeMidThresh: 8230 peak.hbUnderRangeHighThresh: 7335 peak.hbUpperThreshPeakExceededCount: 6 peak.hbUnderRangeHighThreshExceededCount: 3 peak.hbGainStepHighRecovery: 2 peak.hbGainStepLowRecovery: 6 peak.hbGainStepMidRecovery: 4 peak.hbGainStepAttack: 2 peak.hbOverloadPowerMode: 0 peak.hbUnderRangeMidThreshExceededCount: 3 peak.hbUnderRangeLowThreshExceededCount: 3 peak.feedback_apd_low_hb_low: 0 peak.feedback_apd_high_hb_high: 0 debug attr 255: rx0_gain_control_pin_mode value: min_gain_index: 187 max_gain_index: 255 increment_step_size: 1 decrement_step_size: 1 increment_pin: dgpio0 decrement_pin: dgpio0 debug attr 256: rx0_adc_type value: HP debug attr 257: tx1_cals_internal_path_delay_ns value: 1876 debug attr 258: tx1_datapath_loopback_en value: 0 debug attr 259: tx1_mcs_delays value: readDelay: 0 sampleDelay: 0 debug attr 260: tx1_mcs_sample_delay value: 0 debug attr 261: tx1_mcs_read_delay value: 0 debug attr 262: tx1_mcs_strobe_delay value: 65535 debug attr 263: tx1_carrier_hz value: 0 debug attr 264: tx1_capture_delay_us value: 0 debug attr 265: tx1_clgc_filter_alpha value: 0 debug attr 266: tx1_clgc_gain_target_hundredthdB value: 0 debug attr 267: tx1_clgc_loop_open value: 0 debug attr 268: tx1_time_filter_coefficient value: 0 debug attr 269: tx1_immediate_lut_switching value: Y debug attr 270: tx1_counts_greater_than_peak_threshold value: 0 debug attr 271: tx1_counts_less_than_power_threshold value: 4096 debug attr 272: tx1_detection_peak_threshold value: 0 debug attr 273: tx1_detection_power_threshold value: 0 debug attr 274: tx1_rxtx_normalization_upper_threshold value: 33954698 debug attr 275: tx1_rxtx_normalization_lower_threshold value: 3395470 debug attr 276: tx1_additional_power_scale value: 4 debug attr 277: tx1_samples_number value: 4096 debug attr 278: tx1_model_order_tap3 value: 0 debug attr 279: tx1_model_order_tap2 value: 0 debug attr 280: tx1_model_order_tap1 value: 0 debug attr 281: tx1_model_order_tap0 value: 0 debug attr 282: tx1_change_model_tap_orders value: N debug attr 283: tx1_pre_lut_scale value: 8 debug attr 284: tx1_clgc_enable value: 0 debug attr 285: tx1_lut_size value: 1 debug attr 286: tx1_dpd_monitor value: numberOfIterations: 0 numberOfSuccessfulIterations: 0 txPeakPower_100th_dB: 0 rxPeakPower_100th_dB: 0 txAvgPower_100th_dB: 0 rxAvgPower_100th_dB: 0 debug attr 287: tx1_external_path_delay_calibrate value: 0 debug attr 288: tx1_dpd_reset_luts ERROR: Permission denied (13) debug attr 289: tx1_external_path_delay_ps value: 0 debug attr 290: tx1_dpd_enable value: Y debug attr 291: tx1_dpd_config value: numberOfSamples: 4096 additionalPowerScale: 4 rxTxNormalizationLowerThreshold: 3395469 rxTxNormalizationUpperThreshold: 33954696 detectionPowerThreshold: 0 detectionPeakThreshold: 0 countsLessThanPowerThreshold: 4096 countsGreaterThanPeakThreshold: 0 immediateLutSwitching: 1 timeFilterCoefficient: 0 clgcLoopOpen: 0 clgcFilterAlpha: 0 clgcGainTarget_HundredthdB: 0 clgcLastGain_HundredthdB: 0 clgcFilteredGain_HundredthdB: 0 debug attr 292: tx1_dpd_init_config value: enable: 0 amplifierType: 1 lutSize: 0 model: 4 changeModelTapOrders: 0 tap0: 0x1f tap1: 0x7f tap2: 0x1f tap3: 0x1e preLutScale: 2 clgcEnable: 0 debug attr 293: tx1_enablement_delays value: fall_to_off_delay: 0 guard_delay: 0 hold_delay: 0 rise_to_analog_on_delay: 0 rise_to_on_delay: 0 debug attr 294: tx1_rise_to_on_delay_ns value: 0 debug attr 295: tx1_rise_to_analog_delay_ns value: 0 debug attr 296: tx1_hold_delay_ns value: 0 debug attr 297: tx1_guard_delay_ns value: 0 debug attr 298: tx1_fall_to_off_delay_ns value: 0 debug attr 299: tx1_ssi_q_data_delay value: 0 debug attr 300: tx1_ssi_i_data_delay value: 0 debug attr 301: tx1_ssi_strobe_delay value: 0 debug attr 302: tx1_ssi_refclk_delay value: 0 debug attr 303: tx1_ssi_clk_delay value: 0 debug attr 304: tx1_ssi_test_mode_loopback_en value: 0 debug attr 305: tx1_ssi_test_mode_status value: dataError: 1 fifoFull: 0 fifoEmpty: 0 strobeAlignError: 0 debug attr 306: tx1_ssi_test_mode_configure ERROR: Permission denied (13) debug attr 307: tx1_ssi_test_mode_fixed_pattern value: 0 debug attr 308: tx1_ssi_test_mode_data value: TESTMODE_DATA_NORMAL debug attr 309: tx1_dac_boost_en value: 0 debug attr 310: tx1_attenuation_pin_control value: step_size_mdB: 0 increment_pin: dgpio0 decrement_pin: dgpio0 debug attr 311: tx0_cals_internal_path_delay_ns value: 1876 debug attr 312: tx0_datapath_loopback_en value: 0 debug attr 313: tx0_mcs_delays value: readDelay: 0 sampleDelay: 0 debug attr 314: tx0_mcs_sample_delay value: 0 debug attr 315: tx0_mcs_read_delay value: 0 debug attr 316: tx0_mcs_strobe_delay value: 65535 debug attr 317: tx0_carrier_hz value: 0 debug attr 318: tx0_capture_delay_us value: 0 debug attr 319: tx0_clgc_filter_alpha value: 0 debug attr 320: tx0_clgc_gain_target_hundredthdB value: 0 debug attr 321: tx0_clgc_loop_open value: 0 debug attr 322: tx0_time_filter_coefficient value: 0 debug attr 323: tx0_immediate_lut_switching value: Y debug attr 324: tx0_counts_greater_than_peak_threshold value: 0 debug attr 325: tx0_counts_less_than_power_threshold value: 4096 debug attr 326: tx0_detection_peak_threshold value: 0 debug attr 327: tx0_detection_power_threshold value: 0 debug attr 328: tx0_rxtx_normalization_upper_threshold value: 33954698 debug attr 329: tx0_rxtx_normalization_lower_threshold value: 3395470 debug attr 330: tx0_additional_power_scale value: 4 debug attr 331: tx0_samples_number value: 4096 debug attr 332: tx0_model_order_tap3 value: 0 debug attr 333: tx0_model_order_tap2 value: 0 debug attr 334: tx0_model_order_tap1 value: 0 debug attr 335: tx0_model_order_tap0 value: 0 debug attr 336: tx0_change_model_tap_orders value: N debug attr 337: tx0_pre_lut_scale value: 8 debug attr 338: tx0_clgc_enable value: 0 debug attr 339: tx0_lut_size value: 1 debug attr 340: tx0_dpd_monitor value: numberOfIterations: 0 numberOfSuccessfulIterations: 0 txPeakPower_100th_dB: 0 rxPeakPower_100th_dB: 0 txAvgPower_100th_dB: 0 rxAvgPower_100th_dB: 0 debug attr 341: tx0_external_path_delay_calibrate value: 0 debug attr 342: tx0_dpd_reset_luts ERROR: Permission denied (13) debug attr 343: tx0_external_path_delay_ps value: 0 debug attr 344: tx0_dpd_enable value: Y debug attr 345: tx0_dpd_config value: numberOfSamples: 4096 additionalPowerScale: 4 rxTxNormalizationLowerThreshold: 3395469 rxTxNormalizationUpperThreshold: 33954696 detectionPowerThreshold: 0 detectionPeakThreshold: 0 countsLessThanPowerThreshold: 4096 countsGreaterThanPeakThreshold: 0 immediateLutSwitching: 1 timeFilterCoefficient: 0 clgcLoopOpen: 0 clgcFilterAlpha: 0 clgcGainTarget_HundredthdB: 0 clgcLastGain_HundredthdB: 0 clgcFilteredGain_HundredthdB: 0 debug attr 346: tx0_dpd_init_config value: enable: 0 amplifierType: 1 lutSize: 0 model: 4 changeModelTapOrders: 0 tap0: 0x1f tap1: 0x7f tap2: 0x1f tap3: 0x1e preLutScale: 2 clgcEnable: 0 debug attr 347: tx0_enablement_delays value: fall_to_off_delay: 0 guard_delay: 0 hold_delay: 0 rise_to_analog_on_delay: 0 rise_to_on_delay: 0 debug attr 348: tx0_rise_to_on_delay_ns value: 0 debug attr 349: tx0_rise_to_analog_delay_ns value: 0 debug attr 350: tx0_hold_delay_ns value: 0 debug attr 351: tx0_guard_delay_ns value: 0 debug attr 352: tx0_fall_to_off_delay_ns value: 0 debug attr 353: tx0_ssi_q_data_delay value: 0 debug attr 354: tx0_ssi_i_data_delay value: 0 debug attr 355: tx0_ssi_strobe_delay value: 0 debug attr 356: tx0_ssi_refclk_delay value: 0 debug attr 357: tx0_ssi_clk_delay value: 0 debug attr 358: tx0_ssi_test_mode_loopback_en value: 0 debug attr 359: tx0_ssi_test_mode_status value: dataError: 0 fifoFull: 0 fifoEmpty: 0 strobeAlignError: 1 debug attr 360: tx0_ssi_test_mode_configure ERROR: Permission denied (13) debug attr 361: tx0_ssi_test_mode_fixed_pattern value: 0 debug attr 362: tx0_ssi_test_mode_data value: TESTMODE_DATA_NORMAL debug attr 363: tx0_dac_boost_en value: 0 debug attr 364: tx0_attenuation_pin_control value: step_size_mdB: 0 increment_pin: dgpio0 decrement_pin: dgpio0 debug attr 365: mcs_trigger_external value: N debug attr 366: mcs_pulse_external value: N debug attr 367: dev_clkout_div value: 1 debug attr 368: mcs_status value: rf1PllSyncStatus.jesdSyncComplete: 0 rf1PllSyncStatus.digitalClocksSyncComplete: 0 rf1PllSyncStatus.clockGenDividerSyncComplete: 0 rf1PllSyncStatus.sdmClockDividerSyncComplete: 0 rf1PllSyncStatus.referenceClockDividerSyncComplete: 0 rf2PllSyncStatus.jesdSyncComplete: 0 rf2PllSyncStatus.digitalClocksSyncComplete: 0 rf2PllSyncStatus.clockGenDividerSyncComplete: 0 rf2PllSyncStatus.sdmClockDividerSyncComplete: 0 rf2PllSyncStatus.referenceClockDividerSyncComplete: 0 clkPllSyncStatus.jesdSyncComplete: 0 clkPllSyncStatus.digitalClocksSyncComplete: 0 clkPllSyncStatus.clockGenDividerSyncComplete: 0 clkPllSyncStatus.sdmClockDividerSyncComplete: 0 clkPllSyncStatus.referenceClockDividerSyncComplete: 0 clkPllLpSyncStatus.jesdSyncComplete: 0 clkPllLpSyncStatus.digitalClocksSyncComplete: 0 clkPllLpSyncStatus.clockGenDividerSyncComplete: 0 clkPllLpSyncStatus.sdmClockDividerSyncComplete: 0 clkPllLpSyncStatus.referenceClockDividerSyncComplete: 0 firstDigitalSyncComplete: 1 secondDigitalSyncComplete: 1 rfPll1Phase_degrees: 0 rfPll2Phase_degrees: 0 debug attr 369: api_version value: 68.20.12 debug attr 370: ssi_delays value: rx0_ClkDelay: 0 rx0_StrobeDelay: 4 rx0_rxIDataDelay: 4 rx0_rxQDataDelay: 4 tx0_ClkDelay: 6 tx0_RefClkDelay: 0 tx0_StrobeDelay: 4 tx0_rxIDataDelay: 4 tx0_rxQDataDelay: 4 rx1_ClkDelay: 0 rx1_StrobeDelay: 4 rx1_rxIDataDelay: 4 rx1_rxQDataDelay: 4 tx1_ClkDelay: 0 tx1_RefClkDelay: 0 tx1_StrobeDelay: 4 tx1_rxIDataDelay: 4 tx1_rxQDataDelay: 4 debug attr 371: tx_ssi_test_mode_data_available value: TESTMODE_DATA_NORMAL TESTMODE_DATA_FIXED_PATTERN TESTMODE_DATA_PRBS15 TESTMODE_DATA_PRBS7 debug attr 372: rx_ssi_test_mode_data_available value: TESTMODE_DATA_NORMAL TESTMODE_DATA_FIXED_PATTERN TESTMODE_DATA_RAMP_16_BIT TESTMODE_DATA_PRBS15 TESTMODE_DATA_PRBS7 debug attr 373: pll_status value: Clock: Locked Clock LP: Unlocked LO1: Locked LO2: Locked AUX: Unlocked debug attr 374: initialize ERROR: Permission denied (13) debug attr 375: direct_reg_access value: 0x3C No trigger on this device iio:device3: axi-adrv9002-rx-lpc (buffer capable) 2 channels found: voltage0_i: (input, index: 0, format: le:S16/16>>0) 1 channel-specific attributes found: attr 0: sampling_frequency value: 15360000 voltage0_q: (input, index: 1, format: le:S16/16>>0) 1 channel-specific attributes found: attr 0: sampling_frequency value: 15360000 3 device-specific attributes found: attr 0: sync_start_enable value: disarm attr 1: sync_start_enable_available value: arm attr 2: waiting_for_supplier value: 0 3 buffer-specific attributes found: attr 0: data_available value: 0 attr 1: direction value: in attr 2: length_align_bytes value: 8 2 debug attributes found: debug attr 0: pseudorandom_err_check value: CH0 : PN15 : Out of Sync : PN Error CH1 : PN15 : Out of Sync : PN Error debug attr 1: direct_reg_access value: 0xA0300 No trigger on this device iio:device4: axi-adrv9002-rx2-lpc (buffer capable) 2 channels found: voltage0_i: (input, index: 0, format: le:S16/16>>0) 1 channel-specific attributes found: attr 0: sampling_frequency value: 15360000 voltage0_q: (input, index: 1, format: le:S16/16>>0) 1 channel-specific attributes found: attr 0: sampling_frequency value: 15360000 3 device-specific attributes found: attr 0: sync_start_enable value: disarm attr 1: sync_start_enable_available value: arm attr 2: waiting_for_supplier value: 0 3 buffer-specific attributes found: attr 0: data_available value: 0 attr 1: direction value: in attr 2: length_align_bytes value: 8 1 debug attributes found: debug attr 0: direct_reg_access value: 0xA0300 No trigger on this device iio:device5: axi-adrv9002-tx-lpc (buffer capable) 6 channels found: voltage0: (output, index: 0, format: le:S16/16>>0) 3 channel-specific attributes found: attr 0: calibphase value: 0.000000 attr 1: calibscale value: 0.000000 attr 2: sampling_frequency value: 15360000 voltage1: (output, index: 1, format: le:S16/16>>0) 3 channel-specific attributes found: attr 0: calibphase value: 0.000000 attr 1: calibscale value: 0.000000 attr 2: sampling_frequency value: 15360000 altvoltage3: TX1_Q_F2 (output) 6 channel-specific attributes found: attr 0: frequency value: 1999952 attr 1: label value: TX1_Q_F2 attr 2: phase value: 0 attr 3: raw value: 1 attr 4: sampling_frequency value: 15360000 attr 5: scale value: 0.125000 altvoltage2: TX1_Q_F1 (output) 6 channel-specific attributes found: attr 0: frequency value: 1999952 attr 1: label value: TX1_Q_F1 attr 2: phase value: 0 attr 3: raw value: 1 attr 4: sampling_frequency value: 15360000 attr 5: scale value: 0.125000 altvoltage1: TX1_I_F2 (output) 6 channel-specific attributes found: attr 0: frequency value: 1999952 attr 1: label value: TX1_I_F2 attr 2: phase value: 90000 attr 3: raw value: 1 attr 4: sampling_frequency value: 15360000 attr 5: scale value: 0.125000 altvoltage0: TX1_I_F1 (output) 6 channel-specific attributes found: attr 0: frequency value: 1999952 attr 1: label value: TX1_I_F1 attr 2: phase value: 90000 attr 3: raw value: 1 attr 4: sampling_frequency value: 15360000 attr 5: scale value: 0.125000 3 device-specific attributes found: attr 0: sync_start_enable value: disarm attr 1: sync_start_enable_available value: arm attr 2: waiting_for_supplier value: 0 3 buffer-specific attributes found: attr 0: data_available value: 8388608 attr 1: direction value: out attr 2: length_align_bytes value: 8 1 debug attributes found: debug attr 0: direct_reg_access value: 0x90262 No trigger on this device iio:device6: axi-adrv9002-tx2-lpc (buffer capable) 6 channels found: voltage0: (output, index: 0, format: le:S16/16>>0) 3 channel-specific attributes found: attr 0: calibphase value: 0.000000 attr 1: calibscale value: 0.000000 attr 2: sampling_frequency value: 15360000 voltage1: (output, index: 1, format: le:S16/16>>0) 3 channel-specific attributes found: attr 0: calibphase value: 0.000000 attr 1: calibscale value: 0.000000 attr 2: sampling_frequency value: 15360000 altvoltage3: TX1_Q_F2 (output) 6 channel-specific attributes found: attr 0: frequency value: 1999952 attr 1: label value: TX1_Q_F2 attr 2: phase value: 0 attr 3: raw value: 1 attr 4: sampling_frequency value: 15360000 attr 5: scale value: 0.125000 altvoltage2: TX1_Q_F1 (output) 6 channel-specific attributes found: attr 0: frequency value: 1999952 attr 1: label value: TX1_Q_F1 attr 2: phase value: 0 attr 3: raw value: 1 attr 4: sampling_frequency value: 15360000 attr 5: scale value: 0.125000 altvoltage1: TX1_I_F2 (output) 6 channel-specific attributes found: attr 0: frequency value: 1999952 attr 1: label value: TX1_I_F2 attr 2: phase value: 90000 attr 3: raw value: 1 attr 4: sampling_frequency value: 15360000 attr 5: scale value: 0.125000 altvoltage0: TX1_I_F1 (output) 6 channel-specific attributes found: attr 0: frequency value: 1999952 attr 1: label value: TX1_I_F1 attr 2: phase value: 90000 attr 3: raw value: 1 attr 4: sampling_frequency value: 15360000 attr 5: scale value: 0.125000 3 device-specific attributes found: attr 0: sync_start_enable value: disarm attr 1: sync_start_enable_available value: arm attr 2: waiting_for_supplier value: 0 3 buffer-specific attributes found: attr 0: data_available value: 0 attr 1: direction value: out attr 2: length_align_bytes value: 8 1 debug attributes found: debug attr 0: direct_reg_access value: 0x90262 No trigger on this device iio_evgen: 0 channels found: 10 device-specific attributes found: attr 0: poke_ev0 ERROR: Permission denied (13) attr 1: poke_ev1 ERROR: Permission denied (13) attr 2: poke_ev2 ERROR: Permission denied (13) attr 3: poke_ev3 ERROR: Permission denied (13) attr 4: poke_ev4 ERROR: Permission denied (13) attr 5: poke_ev5 ERROR: Permission denied (13) attr 6: poke_ev6 ERROR: Permission denied (13) attr 7: poke_ev7 ERROR: Permission denied (13) attr 8: poke_ev8 ERROR: Permission denied (13) attr 9: poke_ev9 ERROR: Permission denied (13) No trigger on this device iio_sysfs_trigger: 0 channels found: 2 device-specific attributes found: attr 0: add_trigger ERROR: Permission denied (13) attr 1: remove_trigger ERROR: Permission denied (13) No trigger on this device trigger0: xilinx-system-monitor1-convst 0 channels found: No trigger on this device trigger1: xilinx-system-monitor1-samplerate 0 channels found: No trigger on this device root@JUPITERTEST:/# dmesg > dmesg.txt root@JUPITERTEST:/# ls -l dmesg.txt -rw-r--r-- 1 root root 40292 Jan 8 18:40 dmesg.txt root@JUPITERTEST:/# ls bin dev etc init media proc run srv tmp var boot dmesg.txt home lib mnt root sbin sys usr root@JUPITERTEST:/# vi dmesg.txt root@JUPITERTEST:/# cd run/media root@JUPITERTEST:/run/media# ls mmcblk0p1 mmcblk0p2 root@JUPITERTEST:/run/media# cd mmcblk0p1 root@JUPITERTEST:/run/media/mmcblk0p1# ls BOOT.BIN ad_jupiter_stream_test1.elf boot.scr image.ub system.dtb root@JUPITERTEST:/run/media/mmcblk0p1# dmesg > dmesg_after_failure.txt root@JUPITERTEST:/run/media/mmcblk0p1# dmesg [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.12.0adi-v2025.1-27393-gc10fc2e1f7cc (oe-user@oe-host) (aarch64-amd-linux-gcc (GCC) 13.3.0, GNU ld (GNU Binutils) 2.42.0.20240723) #1 SMP Thu Jun 11 09:17:17 UTC 2026 [ 0.000000] Machine model: Analog Devices, Inc. Jupiter SDR [ 0.000000] earlycon: cdns0 at MMIO 0x00000000ff010000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [cdns0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] OF: reserved mem: 0x000000003ed00000..0x000000003ed3ffff (256 KiB) nomap non-reusable memory@3ed00000 [ 0.000000] OF: reserved mem: 0x000000003ef00000..0x000000003ef3ffff (256 KiB) nomap non-reusable memory@3ef00000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000003ecfffff] [ 0.000000] node 0: [mem 0x000000003ed00000-0x000000003ed3ffff] [ 0.000000] node 0: [mem 0x000000003ed40000-0x000000003eefffff] [ 0.000000] node 0: [mem 0x000000003ef00000-0x000000003ef3ffff] [ 0.000000] node 0: [mem 0x000000003ef40000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] cma: Reserved 256 MiB at 0x0000000050e00000 on node -1 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.5 [ 0.000000] percpu: Embedded 31 pages/cpu s89944 r8192 d28840 u126976 [ 0.000000] pcpu-alloc: s89944 r8192 d28840 u126976 alloc=31*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: earlycon console=ttyPS0,115200 root=/dev/ram0 rw [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 524288 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 2MB [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x000000007d500000-0x000000007d700000] (2MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f902f000 [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 33.33MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x7b0074340, max_idle_ns: 440795202884 ns [ 0.000000] sched_clock: 56 bits at 33MHz, resolution 30ns, wraps every 2199023255543ns [ 0.008291] Console: colour dummy device 80x25 [ 0.012473] Calibrating delay loop (skipped), value calculated using timer frequency.. 66.66 BogoMIPS (lpj=133332) [ 0.022798] pid_max: default: 32768 minimum: 301 [ 0.027542] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.034811] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.074745] rcu: Hierarchical SRCU implementation. [ 0.074792] rcu: Max phase no-delay instances is 1000. [ 0.079306] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.087328] EFI services will not be available. [ 0.091930] smp: Bringing up secondary CPUs ... [ 0.096704] Detected VIPT I-cache on CPU1 [ 0.096773] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.097272] Detected VIPT I-cache on CPU2 [ 0.097320] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.097793] Detected VIPT I-cache on CPU3 [ 0.097840] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.097904] smp: Brought up 1 node, 4 CPUs [ 0.131921] SMP: Total of 4 processors activated. [ 0.136620] CPU: All CPU(s) started at EL2 [ 0.140710] CPU features: detected: 32-bit EL0 Support [ 0.145843] CPU features: detected: CRC32 instructions [ 0.151011] alternatives: applying system-wide alternatives [ 0.157681] Memory: 1357604K/2097152K available (23232K kernel code, 3470K rwdata, 19488K rodata, 5376K init, 790K bss, 472952K reserved, 262144K cma-reserved) [ 0.171584] devtmpfs: initialized [ 0.180779] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.184913] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.197823] 19616 pages in range for non-PLT usage [ 0.197842] 511136 pages in range for PLT usage [ 0.197995] pinctrl core: initialized pinctrl subsystem [ 0.209562] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.213701] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations [ 0.220340] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.228283] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.235774] audit: initializing netlink subsys (disabled) [ 0.240904] audit: type=2000 audit(0.160:1): state=initialized audit_enabled=0 res=1 [ 0.248531] cpuidle: using governor menu [ 0.252500] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.259282] ASID allocator initialised with 65536 entries [ 0.273669] platform fd4a0000.display: Fixed dependency cycle(s) with /dpcon [ 0.275122] platform dpcon: Fixed dependency cycle(s) with /axi/display@fd4a0000 [ 0.285680] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.289258] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page [ 0.295533] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages [ 0.302313] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page [ 0.308578] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.315363] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page [ 0.321628] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages [ 0.328412] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page [ 0.402624] raid6: neonx8 gen() 2252 MB/s [ 0.470694] raid6: neonx4 gen() 2207 MB/s [ 0.538774] raid6: neonx2 gen() 2124 MB/s [ 0.606844] raid6: neonx1 gen() 1812 MB/s [ 0.674912] raid6: int64x8 gen() 1415 MB/s [ 0.742989] raid6: int64x4 gen() 1566 MB/s [ 0.811062] raid6: int64x2 gen() 1400 MB/s [ 0.879145] raid6: int64x1 gen() 1033 MB/s [ 0.879191] raid6: using algorithm neonx8 gen() 2252 MB/s [ 0.951211] raid6: .... xor() 1660 MB/s, rmw enabled [ 0.951262] raid6: using neon recovery algorithm [ 0.955592] iommu: Default domain type: Translated [ 0.959928] iommu: DMA domain TLB invalidation policy: strict mode [ 0.972500] SCSI subsystem initialized [ 0.972562] libata version 3.00 loaded. [ 0.972704] usbcore: registered new interface driver usbfs [ 0.976111] usbcore: registered new interface driver hub [ 0.981416] usbcore: registered new device driver usb [ 0.986625] mc: Linux media interface: v0.10 [ 0.990730] videodev: Linux video capture interface: v2.00 [ 0.996229] pps_core: LinuxPPS API ver. 1 registered [ 1.001139] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.010282] PTP clock support registered [ 1.014216] EDAC MC: Ver: 3.0.0 [ 1.017673] zynqmp-ipi-mbox mailbox@ff9905c0: Registered ZynqMP IPI mbox with TX/RX channels. [ 1.026380] jesd204: found 0 devices and 0 topologies [ 1.030965] FPGA manager framework [ 1.034321] Advanced Linux Sound Architecture Driver Initialized. [ 1.041001] Bluetooth: Core ver 2.22 [ 1.043958] NET: Registered PF_BLUETOOTH protocol family [ 1.049254] Bluetooth: HCI device and connection manager initialized [ 1.055605] Bluetooth: HCI socket layer initialized [ 1.060475] Bluetooth: L2CAP socket layer initialized [ 1.065527] Bluetooth: SCO socket layer initialized [ 1.070859] vgaarb: loaded [ 1.078207] clocksource: Switched to clocksource arch_sys_counter [ 1.079504] VFS: Disk quotas dquot_6.6.0 [ 1.083112] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.096464] NET: Registered PF_INET protocol family [ 1.096655] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 1.104649] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 1.111640] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.119373] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.127386] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear) [ 1.135010] TCP: Hash tables configured (established 16384 bind 16384) [ 1.141186] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 1.147853] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 1.155059] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.161014] RPC: Registered named UNIX socket transport module. [ 1.166525] RPC: Registered udp transport module. [ 1.171218] RPC: Registered tcp transport module. [ 1.175915] RPC: Registered tcp-with-tls transport module. [ 1.181396] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.188816] PCI: CLS 0 bytes, default 64 [ 1.192653] Initialise system trusted keyrings [ 1.196322] workingset: timestamp_bits=46 max_order=19 bucket_order=0 [ 1.202723] Trying to unpack rootfs image as initramfs... [ 1.203195] NFS: Registering the id_resolver key type [ 1.213101] Key type id_resolver registered [ 1.217242] Key type id_legacy registered [ 1.221310] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.227952] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.235378] jffs2: version 2.2. (NAND) (SUMMARY) \xc2\xa9 2001-2006 Red Hat, Inc. [ 1.242630] fuse: init (API version 7.41) [ 1.302553] NET: Registered PF_ALG protocol family [ 1.302633] xor: measuring software checksum speed [ 1.307810] 8regs : 2518 MB/sec [ 1.312157] 32regs : 2520 MB/sec [ 1.316589] arm64_neon : 2368 MB/sec [ 1.319555] xor: using function: 32regs (2520 MB/sec) [ 1.324611] Key type asymmetric registered [ 1.328698] Asymmetric key parser 'x509' registered [ 1.333662] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.340963] io scheduler mq-deadline registered [ 1.345483] io scheduler kyber registered [ 1.349535] io scheduler bfq registered [ 1.360135] ledtrig-cpu: registered to indicate activity on CPUs [ 1.399621] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 1.408610] brd: module loaded [ 1.412484] loop: module loaded [ 1.412949] Registered mathworks_ip class [ 1.414544] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.424027] CAN device driver interface [ 1.424665] SPI driver wl1271_spi has no spi_device_id for ti,wl1271 [ 1.430618] SPI driver wl1271_spi has no spi_device_id for ti,wl1273 [ 1.436962] SPI driver wl1271_spi has no spi_device_id for ti,wl1281 [ 1.443312] SPI driver wl1271_spi has no spi_device_id for ti,wl1283 [ 1.449663] SPI driver wl1271_spi has no spi_device_id for ti,wl1285 [ 1.456015] SPI driver wl1271_spi has no spi_device_id for ti,wl1801 [ 1.462369] SPI driver wl1271_spi has no spi_device_id for ti,wl1805 [ 1.468717] SPI driver wl1271_spi has no spi_device_id for ti,wl1807 [ 1.475067] SPI driver wl1271_spi has no spi_device_id for ti,wl1831 [ 1.481419] SPI driver wl1271_spi has no spi_device_id for ti,wl1835 [ 1.487770] SPI driver wl1271_spi has no spi_device_id for ti,wl1837 [ 1.494331] usbcore: registered new interface driver asix [ 1.499536] usbcore: registered new interface driver ax88179_178a [ 1.505634] usbcore: registered new interface driver cdc_ether [ 1.511456] usbcore: registered new interface driver net1080 [ 1.517122] usbcore: registered new interface driver cdc_subset [ 1.523034] usbcore: registered new interface driver zaurus [ 1.528597] usbcore: registered new interface driver cdc_ncm [ 1.534250] usbcore: registered new interface driver r8153_ecm [ 1.541212] usbcore: registered new interface driver uas [ 1.545400] usbcore: registered new interface driver usb-storage [ 1.551441] usbcore: registered new interface driver usbserial_generic [ 1.557915] usbserial: USB Serial support registered for generic [ 1.563920] usbcore: registered new interface driver ftdi_sio [ 1.569663] usbserial: USB Serial support registered for FTDI USB Serial Device [ 1.576971] usbcore: registered new interface driver upd78f0730 [ 1.582883] usbserial: USB Serial support registered for upd78f0730 [ 1.590316] i2c_dev: i2c /dev entries driver [ 1.593984] usbcore: registered new interface driver uvcvideo [ 1.600465] Bluetooth: HCI UART driver ver 2.3 [ 1.603577] Bluetooth: HCI UART protocol H4 registered [ 1.608701] Bluetooth: HCI UART protocol BCSP registered [ 1.614050] Bluetooth: HCI UART protocol LL registered [ 1.619144] Bluetooth: HCI UART protocol ATH3K registered [ 1.624567] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 1.630928] Bluetooth: HCI UART protocol Intel registered [ 1.636222] Bluetooth: HCI UART protocol QCA registered [ 1.641452] usbcore: registered new interface driver bcm203x [ 1.647099] usbcore: registered new interface driver bpa10x [ 1.652668] usbcore: registered new interface driver bfusb [ 1.658142] usbcore: registered new interface driver btusb [ 1.663639] usbcore: registered new interface driver ath3k [ 1.669302] EDAC MC: ECC not enabled [ 1.673090] sdhci: Secure Digital Host Controller Interface driver [ 1.678847] sdhci: Copyright(c) Pierre Ossman [ 1.683177] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.689172] SMCCC: SOC_ID: ID = jep106:0049:0000 Revision = 0x14710093 [ 1.695500] zynqmp_firmware_probe Platform Management API v1.1 [ 1.701217] zynqmp_firmware_probe Trustzone version v1.0 [ 1.738188] zynqmp-aes zynqmp-aes.0: will run requests pump with realtime priority [ 1.740397] zynqmp_rsa zynqmp_rsa.0: This driver is deprecated. Please migrate to xilinx-rsa driver [ 1.749382] usbcore: registered new interface driver usbhid [ 1.754789] usbhid: USB HID core driver [ 1.758808] SPI driver fb_seps525 has no spi_device_id for syncoam,seps525 [ 1.776035] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 (0,8000003f) counters available [ 1.780183] axi_sysid 85000000.axi-sysid-0: AXI System ID core version (1.01.a) found [ 1.787800] axi_sysid 85000000.axi-sysid-0: [jupiter] [USE_RX_CLK_FOR_TX1=0, USE_RX_CLK_FOR_TX2=0] on [sdr] git branch <> git <0> dirty [2026-05-26 13:38:31] UTC [ 1.803146] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered [ 1.808958] usbcore: registered new interface driver snd-usb-audio [ 1.816230] pktgen: Packet Generator for packet performance testing. Version: 2.75 [ 1.827018] Initializing XFRM netlink socket [ 1.827148] NET: Registered PF_INET6 protocol family [ 1.832394] Segment Routing with IPv6 [ 1.835156] In-situ OAM (IOAM) with IPv6 [ 1.839188] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.845494] NET: Registered PF_PACKET protocol family [ 1.849958] NET: Registered PF_KEY protocol family [ 1.854977] can: controller area network core [ 1.859121] NET: Registered PF_CAN protocol family [ 1.863870] can: raw protocol [ 1.866822] can: broadcast manager protocol [ 1.871008] can: netlink gateway - max_hops=1 [ 1.875558] Bluetooth: RFCOMM TTY layer initialized [ 1.880225] Bluetooth: RFCOMM socket layer initialized [ 1.885370] Bluetooth: RFCOMM ver 1.11 [ 1.889117] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 1.894437] Bluetooth: BNEP filters: protocol multicast [ 1.899627] Bluetooth: BNEP socket layer initialized [ 1.904593] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.910504] Bluetooth: HIDP socket layer initialized [ 1.915530] 8021q: 802.1Q VLAN Support v1.8 [ 1.919944] 9pnet: Installing 9P2000 support [ 1.923957] NET: Registered PF_IEEE802154 protocol family [ 1.929340] Key type dns_resolver registered [ 1.933772] NET: Registered PF_VSOCK protocol family [ 1.948836] registered taskstats version 1 [ 1.949017] Loading compiled-in X.509 certificates [ 1.960447] Btrfs loaded, zoned=no, fsverity=no [ 1.960816] alg: No test for xilinx-zynqmp-rsa (zynqmp-rsa) [ 1.986868] domain0: domain0 request failed for node 33: -13 [ 1.986989] xuartps ff000000.serial: error -EACCES: failed to add to PM domain domain0 [ 1.994949] xuartps ff000000.serial: probe with driver xuartps failed with error -13 [ 2.004137] ff010000.serial: ttyPS0 at MMIO 0xff010000 (irq = 25, base_baud = 6249999) is a xuartps [ 2.017368] printk: legacy console [ttyPS0] enabled [ 2.022330] printk: legacy bootconsole [cdns0] disabled [ 2.036450] xilinx-zynqmp-dpdma fd4c0000.dma-controller: Xilinx DPDMA engine is probed [ 2.047474] [drm] Initialized zynqmp-dpsub 1.0.0 for fd4a0000.display on minor 0 [ 3.110267] zynqmp-dpsub fd4a0000.display: [drm] Cannot find any crtc or sizes [ 3.117593] zynqmp-dpsub fd4a0000.display: ZynqMP DisplayPort Subsystem driver probed [ 3.125923] ahci-ceva fd0c0000.ahci: supply ahci not found, using dummy regulator [ 3.133561] ahci-ceva fd0c0000.ahci: supply phy not found, using dummy regulator [ 3.141098] ahci-ceva fd0c0000.ahci: supply target not found, using dummy regulator [ 3.149109] ahci-ceva fd0c0000.ahci: AHCI vers 0001.0301, 32 command slots, 6 Gbps, platform mode [ 3.158000] ahci-ceva fd0c0000.ahci: 2/2 ports implemented (port mask 0x3) [ 3.164878] ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 3.178029] scsi host0: ahci-ceva [ 3.181819] scsi host1: ahci-ceva [ 3.185293] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 33 lpm-pol 0 [ 3.194087] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 33 lpm-pol 0 [ 3.205773] spi-nor spi1.0: SPI-NOR-UniqueID 104000c4820f00041d001b00471c0c32cd [ 3.213623] 4 fixed-partitions partitions found on MTD device spi1.0 [ 3.219998] Creating 4 MTD partitions on "spi1.0": [ 3.224797] 0x000000000000-0x000000100000 : "qspi-fsbl-uboot" [ 3.231687] 0x000000100000-0x000000600000 : "qspi-linux" [ 3.238078] 0x000000600000-0x000000620000 : "qspi-device-tree" [ 3.244908] 0x000000620000-0x000000c00000 : "qspi-rootfs" [ 3.252119] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM [ 3.259062] xilinx-axipmon fd0b0000.perf-monitor: Probed Xilinx APM [ 3.265879] xilinx-axipmon fd490000.perf-monitor: Probed Xilinx APM [ 3.272703] xilinx-axipmon ffa10000.perf-monitor: Probed Xilinx APM [ 3.298522] platform fe200000.usb: Fixed dependency cycle(s) with /axi/i2c@ff030000/usb-pd@38/connector [ 3.516606] ata2: SATA link down (SStatus 0 SControl 330) [ 3.522101] ata1: SATA link down (SStatus 0 SControl 330) [ 4.214275] zynqmp-dpsub fd4a0000.display: [drm] Cannot find any crtc or sizes [ 18.201155] Freeing initrd memory: 376064K [ 18.222821] at24 0-0050: supply vcc not found, using dummy regulator [ 18.230147] at24 0-0050: 2048 byte 24c16 EEPROM, writable, 16 bytes/write [ 18.278952] cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 39 [ 18.285653] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer with timeout 60s [ 18.346266] mmc0: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit [ 18.415083] mmc0: new ultra high speed DDR50 SDHC card at address aaaa [ 18.422600] mmcblk0: mmc0:aaaa SS32G 29.7 GiB [ 18.432177] mmcblk0: p1 p2 [ 19.558232] random: crng init done [ 22.197529] adrv9002 spi0.0: adrv9002-phy Rev 12.0, Firmware 0.22.64, Stream 0.7.18.0, API version: 68.20.12 successfully initialized [ 22.211334] cf_axi_adc 84a00000.axi-adrv9002-rx-lpc: ADI AIM (10.03.\x00) probed ADC ADRV9002 as MASTER [ 22.234593] cf_axi_dds 84a0a000.axi-adrv9002-tx-lpc: Analog Devices CF_AXI_DDS_DDS MASTER (9.02.b) at 0x84A0A000 mapped to 0x000000008c9b8e19, probed DDS ADRV9002 [ 22.262564] cf_axi_dds 84a0c000.axi-adrv9002-tx2-lpc: Analog Devices CF_AXI_DDS_DDS MASTER (9.02.b) at 0x84A0C000 mapped to 0x000000004c6ae300, probed DDS ADRV9002 [ 22.285500] macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 45 (0e:6f:cc:c5:21:28) [ 22.295884] input: gpio-keys-power as /devices/platform/gpio-keys-power/input/input0 [ 22.304007] of_cfs_init [ 22.306480] of_cfs_init: OK [ 22.309344] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 22.365050] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 22.371485] Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' [ 22.378928] clk: Disabling unused clocks [ 22.383874] PM: genpd: Disabling unused power domains [ 22.389253] ALSA device list: [ 22.392222] No soundcards found. [ 22.396031] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 22.398165] Freeing unused kernel memory: 5376K [ 22.404656] cfg80211: failed to load regulatory.db [ 22.409244] Run /init as init process [ 22.417610] with arguments: [ 22.417614] /init [ 22.417618] with environment: [ 22.417621] HOME=/ [ 22.417625] TERM=linux [ 22.434539] systemd[1]: System time before build time, advancing clock. [ 22.442008] systemd[1]: Failed to find module 'autofs4' [ 22.456443] systemd[1]: systemd 255.17^ running in system mode (+PAM -AUDIT -SELINUX -APPARMOR +IMA -SMACK +SECCOMP -GCRYPT -GNUTLS +OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 -LZ4 -XZ -ZLIB +ZSTD -BPF_FRAMEWORK +XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) [ 22.488350] systemd[1]: Detected architecture arm64. [ 22.506339] systemd[1]: Hostname set to . [ 22.511604] systemd[1]: Initializing machine ID from random generator. [ 22.857503] systemd[1]: Queued start job for default target Multi-User System. [ 22.909324] systemd[1]: Created slice Slice /system/getty. [ 22.927550] systemd[1]: Created slice Slice /system/modprobe. [ 22.947511] systemd[1]: Created slice Slice /system/serial-getty. [ 22.967120] systemd[1]: Created slice User and Session Slice. [ 22.986468] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 23.006414] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 23.026434] systemd[1]: Reached target Path Units. [ 23.038315] systemd[1]: Reached target Remote File Systems. [ 23.054310] systemd[1]: Reached target Slice Units. [ 23.066316] systemd[1]: Reached target Swaps. [ 23.103361] systemd[1]: Listening on RPCbind Server Activation Socket. [ 23.122437] systemd[1]: Reached target RPC Port Mapper. [ 23.138860] systemd[1]: Listening on Syslog Socket. [ 23.150512] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 23.171044] systemd[1]: Listening on Journal Audit Socket. [ 23.190634] systemd[1]: Listening on Journal Socket (/dev/log). [ 23.210719] systemd[1]: Listening on Journal Socket. [ 23.222833] systemd[1]: Listening on Network Service Netlink Socket. [ 23.242683] systemd[1]: Listening on udev Control Socket. [ 23.258572] systemd[1]: Listening on udev Kernel Socket. [ 23.274598] systemd[1]: Listening on User Database Manager Socket. [ 23.310594] systemd[1]: Mounting Huge Pages File System... [ 23.319278] systemd[1]: Mounting POSIX Message Queue File System... [ 23.345192] systemd[1]: Mounting Kernel Debug File System... [ 23.361341] systemd[1]: Mounting Kernel Trace File System... [ 23.377496] systemd[1]: Mounting Temporary Directory /tmp... [ 23.394305] systemd[1]: Starting Create List of Static Device Nodes... [ 23.417690] systemd[1]: Starting Load Kernel Module configfs... [ 23.433975] systemd[1]: Starting Load Kernel Module dm_mod... [ 23.449887] systemd[1]: Starting Load Kernel Module drm... [ 23.465949] systemd[1]: Starting Load Kernel Module fuse... [ 23.481931] systemd[1]: Starting Load Kernel Module loop... [ 23.497813] systemd[1]: Starting RPC Bind... [ 23.510701] systemd[1]: File System Check on Root Device was skipped because of an unmet condition check (ConditionPathIsReadWrite=!/). [ 23.529627] systemd[1]: Starting Journal Service... [ 23.546091] systemd[1]: Starting Load Kernel Modules... [ 23.561724] systemd[1]: Starting Generate network units from Kernel command line... [ 23.580967] openvswitch: Open vSwitch switching datapath [ 23.593672] systemd[1]: Starting Remount Root and Kernel File Systems... [ 23.616072] systemd-journald[204]: Collecting audit messages is enabled. [ 23.617695] systemd[1]: Starting Coldplug All udev Devices... [ 23.640549] systemd[1]: Started RPC Bind. [ 23.652005] systemd[1]: Mounted Huge Pages File System. [ 23.670909] systemd[1]: Mounted POSIX Message Queue File System. [ 23.690659] systemd[1]: Started Journal Service. [ 24.007648] systemd-journald[204]: Received client request to flush runtime journal. [ 24.168936] audit: type=1334 audit(1736360578.727:2): prog-id=6 op=LOAD [ 24.169287] audit: type=1334 audit(1736360578.727:3): prog-id=7 op=LOAD [ 24.169425] audit: type=1334 audit(1736360578.727:4): prog-id=8 op=LOAD [ 24.460133] audit: type=1334 audit(1736360579.019:5): prog-id=9 op=LOAD [ 24.460235] audit: type=1334 audit(1736360579.019:6): prog-id=10 op=LOAD [ 24.734335] audit: type=1334 audit(1736360579.287:7): prog-id=11 op=LOAD [ 24.807125] audit: type=1334 audit(1736360579.363:8): prog-id=12 op=LOAD [ 25.050306] macb ff0e0000.ethernet end0: renamed from eth0 [ 25.114725] update-alternatives: Linking /usr/lib/libMali.so.9.0 to /usr/lib/x11/libMali.so.9.0 [ 25.316550] update-alternatives: Linking /usr/lib/libMali.so.9.0 to /usr/lib/x11/libMali.so.9.0 [ 25.415904] Warn: update-alternatives: libmali-xlnx has multiple providers with the same priority, please check /usr/lib/opkg/alternatives/libmali-xlnx for details [ 25.494779] update-alternatives: Linking /usr/lib/libMali.so.9.0 to /usr/lib/x11/libMali.so.9.0 [ 25.682176] update-alternatives: Linking /usr/lib/libMali.so.9.0 to /usr/lib/x11/libMali.so.9.0 [ 28.024473] audit: type=1334 audit(1736360582.583:9): prog-id=13 op=LOAD [ 28.024521] audit: type=1334 audit(1736360582.583:10): prog-id=6 op=UNLOAD [ 28.024811] audit: type=1334 audit(1736360582.583:11): prog-id=14 op=LOAD [ 28.746353] EXT4-fs (mmcblk0p2): mounted filesystem d465aa4b-a261-4b1a-ae94-e88d392318da r/w with ordered data mode. Quota mode: none. [ 28.836461] macb ff0e0000.ethernet end0: PHY [ff0e0000.ethernet-ffffffff:0f] driver [ADIN1300] (irq=POLL) [ 28.836492] macb ff0e0000.ethernet end0: configuring for phy/rgmii-id link mode [ 28.836929] pps pps0: new PPS source ptp0 [ 28.837691] macb ff0e0000.ethernet: gem-ptp-timer ptp clock registered. [ 53.138671] kauditd_printk_skb: 21 callbacks suppressed [ 53.138685] audit: type=1006 audit(1736360607.699:33): pid=878 uid=0 old-auid=4294967295 auid=0 tty=(none) old-ses=4294967295 ses=1 res=1 [ 53.138704] audit: type=1300 audit(1736360607.699:33): arch=c00000b7 syscall=64 success=yes exit=1 a0=8 a1=ffffe7b0a490 a2=1 a3=1 items=0 ppid=1 pid=878 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="(systemd)" exe="/usr/lib/systemd/systemd-executor" key=(null) [ 53.138748] audit: type=1327 audit(1736360607.699:33): proctitle="(systemd)" [ 53.178883] audit: type=1334 audit(1736360607.739:34): prog-id=27 op=LOAD [ 53.178912] audit: type=1300 audit(1736360607.739:34): arch=c00000b7 syscall=280 success=yes exit=8 a0=5 a1=ffffc46f3888 a2=90 a3=0 items=0 ppid=1 pid=878 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="systemd" exe="/usr/lib/systemd/systemd" key=(null) [ 53.178925] audit: type=1327 audit(1736360607.739:34): proctitle="(systemd)" [ 53.178938] audit: type=1334 audit(1736360607.739:35): prog-id=27 op=UNLOAD [ 53.178949] audit: type=1300 audit(1736360607.739:35): arch=c00000b7 syscall=57 success=yes exit=0 a0=8 a1=1 a2=0 a3=ffff86bb3ec0 items=0 ppid=1 pid=878 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="systemd" exe="/usr/lib/systemd/systemd" key=(null) [ 53.178961] audit: type=1327 audit(1736360607.739:35): proctitle="(systemd)" [ 53.179353] audit: type=1334 audit(1736360607.739:36): prog-id=28 op=LOAD [ 115.871958] macb ff0e0000.ethernet end0: Link is Up - 1Gbps/Full - flow control tx [ 195.742443] macb ff0e0000.ethernet end0: Link is Down [ 198.815070] macb ff0e0000.ethernet end0: Link is Up - 1Gbps/Full - flow control tx [ 360.606440] macb ff0e0000.ethernet end0: Link is Down [ 493.272479] adrv9002 spi0.0: Frequency hopping not enabled [ 493.283787] adrv9002 spi0.0: Frequency hopping not enabled [ 494.724599] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 494.761021] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 494.793741] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 494.811048] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 494.847459] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 494.880184] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 494.897541] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 494.933918] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 494.966632] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 494.983892] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 495.020282] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 495.052992] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 901.890790] adrv9002 spi0.0: Frequency hopping not enabled [ 901.902038] adrv9002 spi0.0: Frequency hopping not enabled [ 902.274381] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 902.310827] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 902.343537] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 902.360856] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 902.397283] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 902.429994] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 902.447355] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 902.483732] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 902.516452] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 902.533713] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 902.570103] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 902.602813] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 1025.121824] adrv9002 spi0.0: Frequency hopping not enabled [ 1025.133083] adrv9002 spi0.0: Frequency hopping not enabled [ 1025.507384] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 1025.543773] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 1025.576490] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 1025.593756] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 1025.630142] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 1025.662857] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 1025.680221] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 1025.716591] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 1025.749306] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 1025.766575] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 1025.802964] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 1025.835672] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) root@JUPITERTEST:/# dmesg | grep -i dma [ 0.000000] DMA [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] DMA32 empty [ 0.213701] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations [ 0.220340] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.228283] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.959928] iommu: DMA domain TLB invalidation policy: strict mode [ 2.036450] xilinx-zynqmp-dpdma fd4c0000.dma-controller: Xilinx DPDMA engine is probed [ 3.185293] ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 33 lpm-pol 0 [ 3.194087] ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 33 lpm-pol 0 [ 18.346266] mmc0: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit root@JUPITERTEST:/# dmesg | grep -i adrv9002 [ 22.197529] adrv9002 spi0.0: adrv9002-phy Rev 12.0, Firmware 0.22.64, Stream 0.7.18.0, API version: 68.20.12 successfully initialized [ 22.211334] cf_axi_adc 84a00000.axi-adrv9002-rx-lpc: ADI AIM (10.03.\x00) probed ADC ADRV9002 as MASTER [ 22.234593] cf_axi_dds 84a0a000.axi-adrv9002-tx-lpc: Analog Devices CF_AXI_DDS_DDS MASTER (9.02.b) at 0x84A0A000 mapped to 0x000000008c9b8e19, probed DDS ADRV9002 [ 22.262564] cf_axi_dds 84a0c000.axi-adrv9002-tx2-lpc: Analog Devices CF_AXI_DDS_DDS MASTER (9.02.b) at 0x84A0C000 mapped to 0x000000004c6ae300, probed DDS ADRV9002 [ 493.272479] adrv9002 spi0.0: Frequency hopping not enabled [ 493.283787] adrv9002 spi0.0: Frequency hopping not enabled [ 494.724599] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 494.761021] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 494.793741] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 494.811048] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 494.847459] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 494.880184] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 494.897541] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 494.933918] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 494.966632] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 494.983892] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 495.020282] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 495.052992] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 901.890790] adrv9002 spi0.0: Frequency hopping not enabled [ 901.902038] adrv9002 spi0.0: Frequency hopping not enabled [ 902.274381] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 902.310827] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 902.343537] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 902.360856] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 902.397283] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 902.429994] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 902.447355] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 902.483732] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 902.516452] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 902.533713] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 902.570103] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 902.602813] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 1025.121824] adrv9002 spi0.0: Frequency hopping not enabled [ 1025.133083] adrv9002 spi0.0: Frequency hopping not enabled [ 1025.507384] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 1025.543773] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 1025.576490] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 1025.593756] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 1025.630142] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 1025.662857] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 1025.680221] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 1025.716591] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 1025.749306] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 1025.766575] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 1025.802964] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 1025.835672] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) root@JUPITERTEST:/# dmesg | grep -i iio [ 494.724599] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 494.761021] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 494.811048] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 494.847459] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 494.897541] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 494.933918] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 494.983892] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 495.020282] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 902.274381] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 902.310827] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 902.360856] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 902.397283] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 902.447355] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 902.483732] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 902.533713] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 902.570103] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 1025.507384] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 1025.543773] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 1025.593756] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 1025.630142] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 1025.680221] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 1025.716591] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 1025.766575] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 1025.802964] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. root@JUPITERTEST:/# dmesg | grep -i xilinx [ 1.740397] zynqmp_rsa zynqmp_rsa.0: This driver is deprecated. Please migrate to xilinx-rsa driver [ 1.803146] fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered [ 1.960816] alg: No test for xilinx-zynqmp-rsa (zynqmp-rsa) [ 2.036450] xilinx-zynqmp-dpdma fd4c0000.dma-controller: Xilinx DPDMA engine is probed [ 3.252119] xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM [ 3.259062] xilinx-axipmon fd0b0000.perf-monitor: Probed Xilinx APM [ 3.265879] xilinx-axipmon fd490000.perf-monitor: Probed Xilinx APM [ 3.272703] xilinx-axipmon ffa10000.perf-monitor: Probed Xilinx APM [ 18.285653] cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer with timeout 60s root@JUPITERTEST:/# iio_info | grep iio:device iio:device0: xilinx-ams iio:device1: xilinx-system-monitor (buffer capable) iio:device2: adrv9002-phy [ 2999.704755] adrv9002 spi0.0: Frequency hopping not enabled [ 2999.710405] adrv9002 spi0.0: Frequency hopping not enabled [ 2999.735438] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 2999.766298] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 2999.793515] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 2999.805275] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 2999.836156] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 2999.863373] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 2999.875156] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 2999.906015] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 2999.933235] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) [ 2999.944953] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect_Validate, in line 412, variable name devStateInfo->frequencyHoppingEnabled.Error message Frequency hopping not enabled in device profile. [ 2999.975809] adrv9002 spi0.0: [ERROR]: Error number 3 (0x00000003), Recovery action -2.In file /drivers/iio/adc/navassa/devices/adrv9001/public/src/adi_adrv9001_fh.c, in function adi_adrv9001_fh_HopTable_Inspect, in line 864, variable name NULL.Error message Frequency hopping not enabled in device profile. [ 3000.003028] adrv9002 spi0.0: adrv9002_hop_table_dump_show, 992: failed with "Frequency hopping not enabled in device profile" (3) iio:device3: axi-adrv9002-rx-lpc (buffer capable) iio:device4: axi-adrv9002-rx2-lpc (buffer capable) iio:device5: axi-adrv9002-tx-lpc (buffer capable) iio:device6: axi-adrv9002-tx2-lpc (buffer capable) root@JUPITERTEST:/# cd /sys/kernel/debug/dmaengine root@JUPITERTEST:/sys/kernel/debug/dmaengine# cat summary dma0 (84a30000.dma-controller): number of channels: 1 dma0chan0 | 84a00000.axi-adrv9002-rx-lpc:rx dma1 (84a50000.dma-controller): number of channels: 1 dma1chan0 | 84a0a000.axi-adrv9002-tx-lpc:tx dma2 (84a40000.dma-controller): number of channels: 1 dma2chan0 | 84a09000.axi-adrv9002-rx2-lpc:rx dma3 (84a60000.dma-controller): number of channels: 1 dma3chan0 | 84a0c000.axi-adrv9002-tx2-lpc:tx dma4 (fd4c0000.dma-controller): number of channels: 6 dma4chan0 | fd4a0000.display:vid0 dma4chan1 | fd4a0000.display:vid1 dma4chan2 | fd4a0000.display:vid2 dma4chan3 | fd4a0000.display:gfx0 root@JUPITERTEST:/sys/kernel/debug/dmaengine#