Specialty Amplifiers

Q&A

by Vladimir ALEX Specialty Amplifiers

Latest 20 days ago by Stitch

1726 3 0

Answered
AD5560 Current Clamps accuracy 0
Answered

Hello, I have some quetions about current clamps AD5560. 1) If i do not use offset (CLH, CLL), it is mean that current range is simmetrical (for example -500 mA to 500 mA) 2) I use current range -25...25 mA, then i set CLH 18,75 mA - measuring value...

amplifiers ad5560 Device Power Supply (DPS) & Parametric Measurement Units (PMU) ATE Specialty Amplifiers clamp Show More

1726 3 0
by SteScre Specialty Amplifiers

Latest 1 month ago by SteScre

409 13 0

Not Answered
AD8210 with low sense voltage 0
Not Answered

Deal All, I've a problem with LT Spice simulation of AD8210 (model downloaded from Analog website). I need to measure load current from 0 to 20A. For this purpose, I've designed a circuit with a 4mohm Rsense and REF1, REF2 pins connected to GND for...

hardware Specialty Amplifiers ad8210 Current Sense Amplifiers

409 13 0
by baggio Specialty Amplifiers

Latest 2 months ago by MacManato
166 1 0
Answered
AD5522 Internal COMPARATOR Hysteresis 0
Answered

Hello. I would like to know the hysteresis of the AD5522 COMPARATOR. Can you provide the hysteresis data? Best Regards.

Datasheet/Specs ad5522 Device Power Supply (DPS) & Parametric Measurement Units (PMU) ATE Specialty Amplifiers

166 1 0
by Arikayaaa Specialty Amplifiers

Latest 2 months ago by ianguieb
149 1 0
Answered
Unidirectional current sensing with MAX49925 0
Answered

Does this IC supports unidirectional current sensing if I connect VREF pins to ground?

hardware Specialty Amplifiers sense Unidirectional vref MAX49925 current Current Sense Amplifiers Show More

149 1 0
by jacobeluz Specialty Amplifiers

Latest 2 months ago by jeanmika
265 2 0
Answered
ADA4355 connecting to zedboard and SPI operation 0
Answered

hi I designed a card laying on the eval board of the ada4355 and try to connect it to the zedboard using the FMC connector I am using internal SPI using ZYNQ FPGA (on zedboard to control the ada4355) how do I enable the SPI and I2C to control...

hardware optical transimpedance amplifiers Specialty Amplifiers ADA4355

265 2 0
by LucDL Specialty Amplifiers

Latest 2 months ago by LucDL

457 3 0

Answered
LTSPICE simulation does not converge 0
Answered

Hello, I am currently evaluating an instrumentation chain consisting of LT1997-2 under LTSPICE. The idea is to measure voltages across capacitors, which are currently replaced by capacitors. When I simulate the LT1997-2 with a gain of 0.16 and powered...

amplifiers software LT1997-2 Specialty Amplifiers Difference Amplifiers LTspice 24.1.8 Show More

457 3 0
by Swayash Specialty Amplifiers

Latest 3 months ago by YuriyK1
919 3 0
Answered
I have made a Schematic for MAX12900. Can someone verify it? 0
Answered

Hello, I have made a schematic for MAX12900. I am using it to control a 4-20 mA loop. The circuit is loop powered. So I am using a DC-DC converter to power up the circuit. I have followed the recommended circuits from datasheet. Can someone please verify...

amplifiers MAX12900 Specialty Amplifiers LMXMprodsupport Industrial 4-20mA Driver Show More

919 3 0
by mspalluzzi Specialty Amplifiers

Latest 3 months ago by ADIApproved
123 1 0
Answered
MAX40660 Fab Process 0
Answered

What is the fab process for MAX40660?

MAX40660 Transimpedance Amplifiers (TIA) amplifiers hardware optical transimpedance amplifiers Specialty Amplifiers Show More

123 1 0
by SanghyunPark Specialty Amplifiers

Latest 3 months ago by SanghyunPark

200 2 0

Not Answered
MAX16913A Short-Circuit Detection Current and RSENSE Selection 0
Not Answered

Dear EngineerZone, Currently using the MAX16913A, and we have several questions regarding the short-circuit detection current and RSENSE selection. Based on the datasheet, when RSENSE = 0.65 Ω, the short-circuit detection current can be calculated...

hardware MAX16913A product Specialty Amplifiers MAX16913 Current Sense Amplifiers Show More

200 2 0
by xinxi Specialty Amplifiers

Latest 3 months ago by ADIApproved
178 1 0
Answered
AD694ARZ-REEL mark 0
Answered

Could you please clarify? The markings for 25 years and 24 years are different. May I ask what the original marking represents?

Amplifier-Based Front Ends Datasheet/Specs amplifiers ad694 Specialty Amplifiers Industrial 4-20mA Driver AD694ARZ-REEL Show More

178 1 0
by gautamM Specialty Amplifiers

Latest 3 months ago by maaarmas
174 1 0
Answered
max49921 0
Answered

Hi, I would like to know the Rin_cm and Rin_dm or the Bias current graphs, if available. I am planning to use MAX49921 for a high-side, ultra-precision current-sense application. I want to measure current down to 5 mA with 10 µA accuracy and calculate...

Datasheet/Specs amplifiers MAX49921 Current Sense Amplifiers

174 1 0
by YJI Specialty Amplifiers

Latest 3 months ago by jeobico
220 1 0
Answered
AD633 DC cancel 0
Answered

Hi, We are considering the use of the AD633. To cancel the DC component of (X1-X2)*(Y1-Y2), we are considering applying a negative potential (-1.5V) to the Z terminal. We also plan to perform offset adjustment during product shipment. Is this usage...

Datasheet/Specs Analog Functions Analog Multipliers & Dividers

220 1 0
by Topspin Specialty Amplifiers

Latest 3 months ago by Achim

127 1 0

Not Answered
MAX4210 constant power source oscillates 0
Not Answered

Hi all, I am testing a circuit like this. The IC1 in my case is the MAX4210D and Rsense=1R,Rlimit1=0,Rlimit2=1000R,R1=11k and R2=680R. V+ is 10V and Vcc 5V I have tested two opamp: opamp 1 phase margin 50° and opamp2 phase margin 80°. With opamp2...

hardware MAX4210 Specialty Amplifiers Current Sense Amplifiers

127 1 0
by ian0 Specialty Amplifiers

Latest 4 months ago by GenevaC
292 5 0
Answered
Selectable gain? 0
Answered

I am looking for a device similar to the AD8418 but with pin selectable gain, ideally x20 and x200

hardware Specialty Amplifiers ad8418 Current Sense Amplifiers

292 5 0
by Bera18 Specialty Amplifiers

Latest 4 months ago by ADIApproved
208 1 0
Not Answered
LTC6752 imbalanced Duty Cycle 0
Not Answered

Hey, I'm using LTC6752 comparator By inserting the minus input 1v dc And to the plus input a signal 0.25 and 1.75 volt (so the average voltage is 1) The signal is at 75MHz But the signal at the output has an ruined duty cycle Approximately...

hardware High Speed Comparators (<100ns Propagation Delay) LTC6752 comparators

208 1 0

Popular Forums

Product Forums

Application Forums

Design Center Forums

Highlighted Webinar

Places

Libraries

Upcoming Learning & Events

Challenge Yourself!

What's Brewing

Places

Resources

Visit ContentZone

The Latest Read

New Release

Recent Technical Insights

Q&A

Answered
AD5560 Current Clamps accuracy 0
Answered

Not Answered
AD8210 with low sense voltage 0
Not Answered

Answered
AD5522 Internal COMPARATOR Hysteresis 0
Answered

Answered
Unidirectional current sensing with MAX49925 0
Answered

Answered
ADA4355 connecting to zedboard and SPI operation 0
Answered

Answered
LTSPICE simulation does not converge 0
Answered

Answered
I have made a Schematic for MAX12900. Can someone verify it? 0
Answered

Answered
MAX40660 Fab Process 0
Answered

Not Answered
MAX16913A Short-Circuit Detection Current and RSENSE Selection 0
Not Answered

Answered
AD694ARZ-REEL mark 0
Answered

Answered
max49921 0
Answered

Answered
AD633 DC cancel 0
Answered

Not Answered
MAX4210 constant power source oscillates 0
Not Answered

Answered
Selectable gain? 0
Answered

Not Answered
LTC6752 imbalanced Duty Cycle 0
Not Answered

Q&A

Answered AD5560 Current Clamps accuracy 0 Answered

Not Answered AD8210 with low sense voltage 0 Not Answered

Answered AD5522 Internal COMPARATOR Hysteresis 0 Answered

Answered Unidirectional current sensing with MAX49925 0 Answered

Answered ADA4355 connecting to zedboard and SPI operation 0 Answered

Answered LTSPICE simulation does not converge 0 Answered

Answered I have made a Schematic for MAX12900. Can someone verify it? 0 Answered

Answered MAX40660 Fab Process 0 Answered

Not Answered MAX16913A Short-Circuit Detection Current and RSENSE Selection 0 Not Answered

Answered AD694ARZ-REEL mark 0 Answered

Answered max49921 0 Answered

Answered AD633 DC cancel 0 Answered

Not Answered MAX4210 constant power source oscillates 0 Not Answered

Answered Selectable gain? 0 Answered

Not Answered LTC6752 imbalanced Duty Cycle 0 Not Answered

Answered
AD5560 Current Clamps accuracy 0
Answered

Not Answered
AD8210 with low sense voltage 0
Not Answered

Answered
AD5522 Internal COMPARATOR Hysteresis 0
Answered

Answered
Unidirectional current sensing with MAX49925 0
Answered

Answered
ADA4355 connecting to zedboard and SPI operation 0
Answered

Answered
LTSPICE simulation does not converge 0
Answered

Answered
I have made a Schematic for MAX12900. Can someone verify it? 0
Answered

Answered
MAX40660 Fab Process 0
Answered

Not Answered
MAX16913A Short-Circuit Detection Current and RSENSE Selection 0
Not Answered

Answered
AD694ARZ-REEL mark 0
Answered

Answered
max49921 0
Answered

Answered
AD633 DC cancel 0
Answered

Not Answered
MAX4210 constant power source oscillates 0
Not Answered

Answered
Selectable gain? 0
Answered

Not Answered
LTC6752 imbalanced Duty Cycle 0
Not Answered