Products In This Thread

AD8129 Production
The AD8129/AD8130 are designed as receivers for the transmission of high speed signals over twisted-pair cables to work with the AD8131 or AD8132 drivers...
Datasheet
AD8129 on Analog.com

  • State Not Answered
  • Replies 2 replies
  • Subscribers 24 subscribers
  • Views 497 views
  • Users 0 members are here
Options
Related 

        

            Post
             Go back to editing
        

    

    


    

    









		












	
	
			
	
			
		
	
	
		

		
AD8129/AD8130 Power Sequence



		

			

									
					    cmontoya
					
							

			
				
									
											
			
			
				
    
			
			
			    	
			                    
                
				                on Apr 8, 2021 
				
			
			
		
    

				
		
    
		    		    
		    
		    	
			
    So I have an AD8129 in my design, would there be an issue with powering the negative rail for 400mS longer than the positive rail during shut down. Were trying to figure out why they keep dieing on us. We have tried diodes  across inputs with no luck.  We our operating with a gain of 4.6, But stability doesn't seem to be the issue, my theory had been it was oscillating it's self to death but. Nether diodes or higher gain seems to work. Once the amp "Dies" it's noise output sky rockets.  
    

    

    circuit :
    

     
    
								
    

				
				
		
    
			
						
									
									
						
						
			
			
			
			
		
    

        
        

					
    
			
    


    


	
    
		
	
    















    
	
    
	
    
					



			








	
	
	
	



Parents
	
      
	

    • 
	
      



	
		
	
	



      
	
      
		
      
							
					
      
		
      
			
													0
							
			
				
									
							        
			
			
			
        
            
			                            
                        
                on Apr 16, 2021 1:11 AM
            
            
					
        
	
        

		
		
        
					
        We have tried adding diodes, cranking gain to 11. with no luck. But if we built this amp in Isolation we did find that if we left the negative rail on to long at power down that would create the problem.  so we addressed the 400mS of time that the negative rail remained high at shut down that seemed to ameliorate the problem but not solve it.  Any insight from analog devices, or other users would be appreciated.  
        
			
        

		
		
		
		
	
        
	
        
		
        
			
		
        
	
        
	
        
		
						
						
				
						
				
				
		
		
        
			
		
        
	
        

        

        • 

	

      • 
	
        



	
		
	
	



        
	
        
		
        
							
					
        
		
        
			
													0
							
			
				
									
							        
			
			
			
        •  Analog Employees  
        
            
			                            
                        
                on May 17, 2021 7:14 PM
            
            
												
						in reply to cmontoya
					
									
        
	
        

		
		
        
					
        Hi Chris,
        

        I want to apologize for the delay in getting back to you.
        

        Is it at all possible for you to remove the delay on the negative side to see if the issue goes away?
        

        If not, can you add a larger cap on the positive side to make the 400ms delay much shorter? 
        

        That would be my initial attempt to see if that is what is causing the problem. 
        

        Also, is the part getting hot at all? Is it possible for you to email your full schematic 
        to CIC.americas@analog.com so I can take a look at it?
        

        Thanks
        

        Charly
        
			
        

		
		
		
		
	
        
	
        
		
        
			
		
        
	
        
	
        
		
						
						
				
						
				
				
		
		
        
			
		
        
	
        

        

        • 

	
      



Reply

        


      • 
	
        



	
		
	
	



        
	
        
		
        
							
					
        
		
        
			
													0
							
			
				
									
							        
			
			
			
        •  Analog Employees  
        
            
			                            
                        
                on May 17, 2021 7:14 PM
            
            
												
						in reply to cmontoya
					
									
        
	
        

		
		
        
					
        Hi Chris,
        

        I want to apologize for the delay in getting back to you.
        

        Is it at all possible for you to remove the delay on the negative side to see if the issue goes away?
        

        If not, can you add a larger cap on the positive side to make the 400ms delay much shorter? 
        

        That would be my initial attempt to see if that is what is causing the problem. 
        

        Also, is the part getting hot at all? Is it possible for you to email your full schematic 
        to CIC.americas@analog.com so I can take a look at it?
        

        Thanks
        

        Charly
        
			
        

		
		
		
		
	
        
	
        
		
        
			
		
        
	
        
	
        
		
						
						
				
						
				
				
		
		
        
			
		
        
	
        

        

        • 


      


Children
	
      No Data